Jump to content
SAU Community

Just Bought A 32, Where Are Some Good But Reasonably Priced Workshops In The South East?

V-Spec

By V-Spec,
in Victoria

 Share

Recommended Posts

V-Spec Rising Star

V-Spec

Posted
Posted (edited)

Just picked up a mates gtst for a pittance but it needs some serious attention mechanically

I used to take my GTR to RE customs but it looks like their phone is off, ill go by their after work to see if they're still open

Can someone recommend a good reliable but reasonably priced workshop in the south east i can get it towed to, cant trust the drive, rather spend on a tow than damage the hydraulic / power steering system and cooling system.

ive read on hear about sabbadin automotive being ok, would like other suggestions, will try speak to both these people after work today

thanks in advance

Rich

Edited by V-Spec
V-Spec Rising Star

V-Spec

Posted
  • Author
Posted

i live south east, i know chasers is good but ill go speak to OTR, Sabbadin and see what happened to RE customs

anyone know if RE is still around, all these shops are relatively close to each other

thanks for the quick replys and information!!

what shop would be the best to source second hand parts and install them?

Birds Grand Master

Birds

Posted
Posted

I thought otr is a supplier?

Sabbadin is great!

Chasers would be my bet

They have a workshop...they do very cheap work. My turbo install was $280 including removal and replacement of broken exhaust manifold studs.

V-Spec Rising Star

V-Spec

Posted
  • Author
Posted (edited)

wait, birds, were you talking about Sabbadin or chasers or your original recommendation of OTR?

im a bit giddy about the car, i re-read the thread and i think you mean OTR

Thanks!

Edited by V-Spec
Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted

RE customs moved shop to a few factories down. my run-ins with them over the last 12 months have not been positive.

+1 for sabbadin, also Ace Dyno + workshop in clayton is round that area. Anthony is a good guy.

Birds Grand Master

Birds

Posted
Posted

Was talking about OTR...nice and helpful guys. Sabbadin also do great work, I don't imagine them being as cheap as OTR though.

htial Grand Master

htial

Posted
Posted

Brad from RE now works at RTR in Dandenong. I had them do a wheel bearing and a service and we had the Member Renewal / Dyno Day there. I'll be going back for sure.

Sunkist Grand Master

Sunkist

Posted
Posted

Was talking about OTR...nice and helpful guys. Sabbadin also do great work, I don't imagine them being as cheap as OTR though.

yeh sabbadin arent the cheapest, but you definitely pay for a good job done. hes worked on all of my cars.

Ive taken birds advice and organized things with OTR Rich

nice! i never knew they did service work, definitely wouldve gone to them if I knew

Brad from RE now works at RTR in Dandenong. I had them do a wheel bearing and a service and we had the Member Renewal / Dyno Day there. I'll be going back for sure.

RTR is great, great mechanics there, but are a little expensive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...