Jump to content
SAU Community

Just Bought A 32, Where Are Some Good But Reasonably Priced Workshops In The South East?


Recommended Posts

Just picked up a mates gtst for a pittance but it needs some serious attention mechanically

I used to take my GTR to RE customs but it looks like their phone is off, ill go by their after work to see if they're still open

Can someone recommend a good reliable but reasonably priced workshop in the south east i can get it towed to, cant trust the drive, rather spend on a tow than damage the hydraulic / power steering system and cooling system.

ive read on hear about sabbadin automotive being ok, would like other suggestions, will try speak to both these people after work today

thanks in advance

Rich

Edited by V-Spec

i live south east, i know chasers is good but ill go speak to OTR, Sabbadin and see what happened to RE customs

anyone know if RE is still around, all these shops are relatively close to each other

thanks for the quick replys and information!!

what shop would be the best to source second hand parts and install them?

I thought otr is a supplier?

Sabbadin is great!

Chasers would be my bet

They have a workshop...they do very cheap work. My turbo install was $280 including removal and replacement of broken exhaust manifold studs.

wait, birds, were you talking about Sabbadin or chasers or your original recommendation of OTR?

im a bit giddy about the car, i re-read the thread and i think you mean OTR

Thanks!

Edited by V-Spec

RE customs moved shop to a few factories down. my run-ins with them over the last 12 months have not been positive.

+1 for sabbadin, also Ace Dyno + workshop in clayton is round that area. Anthony is a good guy.

Was talking about OTR...nice and helpful guys. Sabbadin also do great work, I don't imagine them being as cheap as OTR though.

Brad from RE now works at RTR in Dandenong. I had them do a wheel bearing and a service and we had the Member Renewal / Dyno Day there. I'll be going back for sure.

Was talking about OTR...nice and helpful guys. Sabbadin also do great work, I don't imagine them being as cheap as OTR though.

yeh sabbadin arent the cheapest, but you definitely pay for a good job done. hes worked on all of my cars.

Ive taken birds advice and organized things with OTR Rich

nice! i never knew they did service work, definitely wouldve gone to them if I knew

Brad from RE now works at RTR in Dandenong. I had them do a wheel bearing and a service and we had the Member Renewal / Dyno Day there. I'll be going back for sure.

RTR is great, great mechanics there, but are a little expensive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...