Jump to content
SAU Community

What Size Dumppipe For 500Hp

nick81xd

By nick81xd,
in Engines & Forced Induction

 Share

Recommended Posts

nick81xd Community Regular

nick81xd

Posted
Posted

Tried searching but must be hopeless at using it. Also the 25 thread is full of small turbo results.

Have a 25 with a 3582r plain wheel turbo.

I have a full 3 inch turbo back exhaust with a resonator and rear cannon on it but I'm struggling with small amount of exhaust backpressure pushing open gate under full noise.

I am thinking the dump pipe might be a tad small With the wastegate plumbed back in. I'm aiming for 500+ (currently at 471hp).

looking at what people's opinions/experirence are on What size exhaust they have.

I have enough room for 4 inch but don't want to go oversized if not necessary.

Go with posts.

Link to comment
https://www.sau.com.au/forums/topic/425650-what-size-dumppipe-for-500hp/
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

A free flowing exhaust would just make it worse I think. You need to increase the wastegate actuator spring tension to help hold the manifold pressure in.

What is your base (minimum) actuator pressure?

XRATED Veteran

XRATED

Posted
Posted

4" = no restriction.

Saying that, plenty of people have made 500bhp on a proper 3" exhaust with open screamers.

Personally I'd go with a 3.5" dump to tip, magnafolw muffler and a free flowing rear can of choice... Here's the thing though, make the waste-gate dump pipe larger and longer than you might think. Run it right down and merge it just before the cat in a nice long, shallow angle transition.

nick81xd Community Regular

nick81xd

Posted
  • Author
Posted

i have 14psi actuator springs in. its a turbosmart 50mm gate.

I cant stand the sound of a screamer pipe so plumbback is a MUST..
the gate pipe is about 60cm long joining in just before the cat area so i think having a bigger diameter exhaust in a copy of current setup will do the trick.

I just dont want to go to hassle of doing 3.5inch only to need a 4 inch down the track

GTScotT Grand Master

GTScotT

Posted
Posted

There is no oversize with a dump pipe imho. 4" will work fine.

However I don't think that's your issue, you should be able to get away with a 3". Have you tried a heavier WG spring as mentioned above?

nick81xd Community Regular

nick81xd

Posted
  • Author
Posted

There is no oversize with a dump pipe imho. 4" will work fine.

However I don't think that's your issue, you should be able to get away with a 3". Have you tried a heavier WG spring as mentioned above?

i have changed the way the gate signal is being sent and it helped sort of. its either 16psi base and wont bleed past 21psi as a single connection onto wastegate or as a 2 port connection its 23psi minimum bleeding up to the 26psi wanted.

I would like to run 18psi low and 26psi high settings so changing the spring pressure up closer to higher settings is something im trying to avoid

scotty nm35 Grand Master

scotty nm35

Posted
Posted

At what boost? 7psi is fark all spring...

I am running 26psi of spring, and after a few track days the tension has dropped back, now it only runs 19 psi off the spring. If you plumb pressure onto the top of the gate also you should be ok either way, mine easily runs a flat 32psi now with the 5 port Mac.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

I have a 3 inch dump, and 2 inch off the 45mm gate. As long as they flow well and merge gradually into a 3.5 inch free flowing system you should crack 400kw with it fairly easily. Mine would be making that if I had a manual box...

abr33 Proficient

abr33

Posted
Posted (edited)

At what boost? 7psi is fark all spring...

I am running 26psi of spring, and after a few track days the tension has dropped back, now it only runs 19 psi off the spring. If you plumb pressure onto the top of the gate also you should be ok either way, mine easily runs a flat 32psi now with the 5 port Mac.

22 psi, barely falls over any more than half a pound at 7700. Im running e-boost and pressure to both sides of gate respectively

Edited by abr33
nick81xd Community Regular

nick81xd

Posted
  • Author
Posted (edited)

Is that no fit in a r32 with a 25 in it stao? What fouled?.

I want to run plumbed in no matter what so can't include screamer. I prefer to hear the engine while its making noises not finding out after when its brokent

Edited by nick81xd
34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

Is that no fit in a r32 with a 25 in it stao? What fouled?.

I want to run plumbed in no matter what so can't include screamer. I prefer to hear the engine while its making noises not finding out after when its brokent

It shouldn't make noises :/

Kurtis ran 500hp with the gate plumbed back and 3inch system....

Mine is a screamer so results are irrelevant I guess.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
    • oHBoy.
      Starter motor replacment teeth count.

      By oHBoy. · Posted

      lights are on just the one click.  
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Absolutely matters because, while a temperature change will eventually reach a sensor at the end of a static line, the response time is far far far too slow to be useful. Might as well not have a temp gauge at all.
    • f00stx
      Anyone running the VQ37VHR with forced induction?

      By f00stx · Posted

      When I was eyeing off the 370GT (after deciding I didn't want to spend 30-40k+ to relive my early 20s in an R33) I thought it'd be a good project to add a turbo to it. Now that I have a 370GT, and I've had a couple of chances to open it up, I'm pretty stunned by how much power it makes 🫠 Honestly, the way the VVEL opens it up, it almost feels like there's a little turbo tucked away in there somewhere. It's like Nissan looked at VTEC and said "hold my beer" 😁 Has anyone thrown a turbo into their 370Z or 370GT? Is there a conservative boost level you can run without having to upgrade the fuel system, or are bigger injectors and a bigger pump a given?
×
×
  • Create New...