Jump to content
SAU Community

Recommended Posts

I have recently bought a 96 import r33 gtst and i am having some problems, firstly being boost, the stock boost gauge just barely gets past 0 at the high end of the rev range (cant see exactly because tacho is not working atm which is another story).

The other thing which could be related is there is a high pitch whistle noise which doesnt sound right at all which sounds like its coming from around the turbo when it gets to high revs. I cant see any apparent split hoses, could this be a leak on the manifold side?

Any advise would be much appreciated before i start dismantling on the weekend.

Hmm no its a different noise, it wont get close to boost till high revs and then it starts making the noise and will get to maybe +1 mm/hg at the most.

Ill have to get a vid of it tomorrow and post it up.

No the car wasn't exactly cheap. Tonight i disconnected the bottom vacuum line from the stock solenoid and i seemed to make 6-7 psi, was about half way from 0 to 7 mmhg. I also got a clip of the noise:

Sounds like a fat exhaust leak. Check for obvious visual signs. You should see black carbon deposits n shit from where the leak is. Since you said you aren't making boost, I'd check for the obvious signs around the manifold to turbo gasket. Then check turbo to dump pipe. Mine made that exact same sound. The metal gasket between the turbo and dump was split from reuse. Don't get those paper kind of gaskets, those two shiny things on the black shit. They are shit, piss weak and don't last. Get the proper metal gasket. I don't think a failing turbo would emit that sound. My car when I got it had surprisingly loose mani to head nuts. I tightened those up quick fast.

hmm, i was going to pull it all apart this weekend but i cant get the replacement gaskets till after monday through nissan. Thanks for the info, might pull a few things out of the way and have a look for signs of a leak as you say. Not that i can see it very well but i think there is a broken stud on the manifold to head too.

It sounds to me that it's not an exhaust leak. Probably the Turbo is gone but also check the Blowoff valve to see if it's fallen loose. This happened to me and turned out the BOV had given way over time.

  • 3 weeks later...

All the nuts on the turbo to manifold were loose, i tightened them up and ordered a new gasket. Would this be enough to cause complete lack of boost or is it likely to have a boost leak somewhere as well? car seems to be running very rich especially at idle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...