Jump to content
SAU Community

Recommended Posts

Be careful going higher because if you go too high the stock shock will be at its full length of travel and won't work at all, it will bounce everywhere. My friend and I tried it on a commy ute and the rear lifted off the ground when braking hard

Well now they're getting cheaper at the bottom end, I think a grubby C34 would make a great softroader, basically.
Some slightly larger diameter all-terrain tyres (235/60R16 looks good and fairly common) would get a little clearance but at the same time would need a little more height to help guard clearance. I was thinking along the lines of stiffer springs and some strut top spacers.

I actually had a think about this as an option for a touring wagon/beach buss/camping wagon.

My stag is reasonably low. Honestly I don't have too many issues with driveways, speed humps or parking bollards (my front lip will clear a standard height concrete parking bollard by 2-3mm). We started taking it camping and day trips.... perfect for a blast up the east coast (Tassie) then cruise into a camping spot, most of the camping places are down dirt roads, on sand and washed out potholes. I'm surprised were I was able to take it..... the center diff lock and snow mode is great in rolled gravel or sand, just as long as you straddle the rutts :yes: . A couple of times I could actually go places the big 4WD guys couldn't go :woot: under fallen trees etc.

We ended up buying the missus an xtrail, suits her gutter riding duties better ( :no: my poor volk GTC's).

Long story short:

I was going to space up the sub-frames and between the shock and shock tower. Throw on some more off roadish taller tyres. Then use some aftermarket arms with slighlty longer stroke shocks/springs.

J

Hmm, I have some spare front shock absorbers for the stagea lying around. Theyre stagea specific ones and theyre slightly longer than GTR shocks. Longer stroke to the piston.

I guess theyre for what youre talking about. Most stageas are/were family wagons and snow cars, not sports cars.

Your biggest issues will be keeping the correct geometry if you change the relationship of factory pickup points/shock-spring length. The rebound geometry past horizontal gets squew wiff pretty quick.

If you space the sub-frames the same amount as the shock spacers, it keeps everything relatively sock for geometry/bump-steer etc If effect a 'body' lift.

XRATED, thats the same kind of thing that got me thinking, I've crawled into a few places it by all rights shouldn't have been, it seems very competent getting around on gravel and sand, through muddy paddocks and up and over stuff.

I think the rear subframe could be spaced down, isn't the upper arm in the front mounted to the chassis though? so I'm guessing that wouldn't work for the front. Ours seems to have a little negative camber on the back at stock height so I'm guessing a little bit of lift via spring/strut there wouldn't hurt, front I'm not so sure how much you could lift without going into positive camber.

Clearance wise I think with early bumpers, no skirts and no lips it wouldn't be too bad, sump does hang pretty low but could always run a bashguard tied back to the crossmember.

Edited by floody

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...