Jump to content
SAU Community

Recommended Posts

Attendees (24)

Ruxis(Jarrad)-Evo7-newy
LukeGTR-32GTR(hopefully)-Sydney

Owens-33GTR-Sydney

Newbie34-34?-Sydney

Blackline33-33gtst?-Sydney

GeeTeeTee-34gtt-newy *Nominated Hoon*

Benji-s15-newy *panel gap inspector*

Aus_Delivered-32GTR-Sydney

mjh-34gtt-newy

GTR34A-34GTR-newy

ben34-34gtt-Cessnock

YE34OK-34-Sydney

FeZ25-34-somewhere south :P

R34liner-34GTR-Sydney

reaper-Sydney

t5iv-Brand new pulsar on a test drive-Sydney :P

DeKa-??

Terry-one of his trophies-Sydney

Crashdown-Sydney

Redlinegtr-GTR-Sydney

boxheadr33-33gtst-Sydney

Wagonboy-Stagea-Sydney

Osborn-Stagea-Sydney

Dori34-Evo7-Sydney

Maybe

SiNNo-Evo-Sydney

r32gojira-32?

r33huntme-33

Anyone want footage of their car? :P

4l0gnl.jpg

I'll meet you guys at the halfway point on putty road. I'm leaving from Mcdonalds on windsor and grove ave, and heading up putty rd, will probably leave Macca's at around 10am to get at halfway point for 11:30am

will be here with you guys and gals.

Lol and bring it to the cruise?

on some nissans(if they have a regod demo), some dealerships offer an overnight test drive.

so you can drive when/where you normally do to see what the cars really like.

doooo eeeet....

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...