Jump to content
SAU Community

2013/14 Sau Qld Annual General Meeting (Agm) And Committee Elections


Recommended Posts

Haha, my monies on "what have u done, no cover" lol

Age: 21 ie immature

Car: Nissan hoon mobile cat drowner ie skyline

Mods: engine/gearbox ie you've installed a torture device to avoid taxes

Coverage: nothing, infact u owe Shannon's one million dollars

I know what it's like to have to put together an Agenda for a major meeting, Lots of scotch and spell check and it's all good,

Your's and Miss R34's efforts are appreciated even by those of us too lazy to fill out our membership form.

Edited by RandomHero83

I know what it's like to have to put together an Agenda for a major meeting, Lots of scotch and spell check and it's all good,

Your's and Miss R34's efforts are appreciated even by those of us too lazy to fill out our membership form.

Fill out a Membership form NOW and hand McFly monehs tonight. Just sayin' :P

ANNOUNCEMENT

Due to both Scott (Sabbai) and myself being nominated for the President's position, there will be a vote tonight. Have a long hard think about who you wish to have as the head of your Club. Chants will be collecting votes whilst I exit the room. Scott has taken exiting the room to a whole new level and is currently in the UK :P

I just assume it's always suits for you :P

Righto, I have a feeling ill be training it in if that's an option, what's the best station to get off at?

I'm guessing Milton :/

Fill out a Membership form NOW and hand McFly monehs tonight. Just sayin' :P

This. No excuses for non members, the online form takes 10 seconds to fill in: https://docs.google.com/forms/d/17Hv7fsU_nG3cjJDF_F6vqajgoH6H8h5gNeHJ2ul5K9Y/viewform

I will also have some paper forms with me tonight, and we will be taking cash payments for memberships.

AGM Agenda is up.

I've posted it in the members section to keep some privacy but we can keep the conversation happening here.

http://www.skylinesaustralia.com/forums/topic/430893-2013-annual-general-meeting-documents/#entry6989343

Let us know what you think. Tonight, your voice will be heard!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...