Jump to content
SAU Community

Recommended Posts

Step 1. Undo the clamps on either side of this U-Shaped hose, then remove the hose.

UHose.jpg

Step 2. Undo these 2 screws, it will allow you lift up the intake pipe giving you more room.

2nuts.jpg

Step 3. Loosen the 2 adjustable clamps on the hose connecting to the plenum, also the other small one seen in the picture.

plenum.jpg

Step 4. Disconnect the loom plug (may vary in appearance). Then just move 2 disconnected looms off to the side. You don't have to remove the 2 circled screws.

loom.jpg

Step 5. There are 8 allen screws to undo all the way along the plastic cover as circled below. Once you have removed them all you can then slide out the plastic cover.

rockercover.jpg

Step 6. Once you have removed the plastic cover you'll see the lead pictured below, with 6 looms connecting to the top of each coilpack, undo the looms that connect to the top of each coilpack. Then remove the small screws that hold the length of cable in place and remove it.

(Coil Pack Lead)

somecable.jpg

nocover.jpg

Step 7. Now, at this stage you will see the top of each coil pack, I pulled out the whole cradle and coil pack as described next but you dont have to that. You can just remove the screws that hold each coil pack in. This how to pull it all out.

Unscrew the gold/bronze bolts that hold the coil pack cradles in place. There is about 6 or 7 of them. Once they are removed you can pullout the coilpacks and cradle to see the spark plugs underneath.

(Top of Coil Packs)

noloom.jpg

(Coil Packs and Cradle)

coilpacks.jpg

Step 8. Now that you can see inside, it is recommended that you spray some compressed air inside to clear/dislodge any crap that may fall into the combustion camber once you have taken out the spark plugs. Now remove the spark plugs and put in the new ones!

Step 9. Put it all back together.

Edited by Shane
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/42819-rb25det-changing-the-spark-plugs/
Share on other sites

  • 4 weeks later...
  • 2 months later...
  • 1 month later...

had the plugs in mine done a few weeks ago. Used NGK iridiums to suit rb25det.

Took in for a tune the other day and had problems. Apparently I should have used NGK iridiums to suit rb20det as they run cooler. She runs nicely now and the plugs are cheaper!

  • 9 months later...

anyone know if you just pull the coilpacks straight out once the two screws are removed?

seems like the pack is still attached to something underneath and i'm not game enough to put too much force into pulling it out without knowing.

had the plugs in mine done a few weeks ago. Used NGK iridiums to suit rb25det.

Took in for a tune the other day and had problems. Apparently I should have used NGK iridiums to suit rb20det as they run cooler. She runs nicely now and the plugs are cheaper!

Hey so which one should you use?

rb20 or rb25 sparks? should you also get it tuned after the installing the new sparks?

I love this tutorial.

Found it over a year ago, made it into word doco format.

Printed it off in colour and make sure it's around everytime i change em juts to be sure.

Thanks matey !

Awesome job!

Used the changing oil one for awhile but thats piiiss easy so don't need it now.

(but not easy if you've never done it before, which is where i was awhile back)

The best thing is, changin oil and spark plugs must be 80% of what a 'service' is and you never know exactly what they're doing........so get in there guys and do it yourself.

  • 4 weeks later...

Would the author of this tutorial please add:

Loosen the plugs, BUT before removing them, blow the area thoroughly clean with compressed air.

Can't believe people still pull dirty plugs and wonder why they suddenly develop a miss after dislodging crap into the combustion chamber.

Regards.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...