Jump to content
SAU Community

Recommended Posts

Hi guys, just looking to clear up a few things. the ye olde search fuction has failed me. lots of info of anti theft set ups but looking for motorsports/Cams legal setup

I'm looking to install a kill switch, obviously.

i want the most simple setup i can get away with, what do i need to be cutting? its a 33 so battery is still in the boot, do i run a switch in the engine bay in the pos cable off the alternator and run one pull cable to the scuttle panel infront of the drivers A pillar and a second cable into the car mounted to the cage or somwhere so its able to be pulled from outside and inside?? should i be cutting from the battery instead? the kill switch i looked at is a grayston unit with the extra pins and resistor etc, do i have to cut the ign out aswell?

i could of sworn i saw a install on here yonks ago by maybe (duncan)?? it looked as tho the battery was in the boot, the pos cables were run up to behind the handbrake area to a plastic jaycar spec box to the kill switch the back to the battery. maybe i dreamt it up

any help greatly appreciated, cheers

my 32 has had battery moved into the boot, positive cable is run through the cabin via the battery switch,

and the auto elec used the alternator warning light to stop the car when the switch is turned off.

the alternator warning light is what excites it to charge, so if it's switched off it kills the car, only drama is it

can also kill the alternator..

Cheers

Kill switch needs to cut the positive battery lead and the positive feed to the alternator, doesn't have to cut the ignition separately. Cutting the alternator warning light wire will only stop the alternator from exciting it won't stop it from charging while driving.

Kill switch needs to cut the positive battery lead and the positive feed to the alternator, doesn't have to cut the ignition separately. Cutting the alternator warning light wire will only stop the alternator from exciting it won't stop it from charging while driving.

It did on my car, even had to wire the warning light to my digital dash, because the alternator would not charge without it,

no charge from the alt + cut battery power equals car wont run..

It did on my car, even had to wire the warning light to my digital dash, because the alternator would not charge without it,

no charge from the alt + cut battery power equals car wont run..

Unusual, most of the time you can get the alternator to kick in by revving it hard enough even without the globe if it hasn't been sitting for too long and has held some residual magnetism. I would still recommend doing it with the actual positive feed to the alternator.

Yeah that was on Neil's race car (http://www.skylinesaustralia.com/forums/topic/341836-neils-r33-gts-t-build/) It was run that way to retain the standard undercar main positive to the starter and front, so basically the + terminal runs to the switch near the seat, and then back to the boot. There are shorter was to cut it if necessary. It uses a dual pole switch to cut both the main battery and the main ignition (via a big relay).

I've used a similar cut off in my race car (ie relay to cut ignition) but I'm not really happy with it in either car because the relay will eventually drain the battery unless the kill switch is pulled.

I'd love to hear a better way to do it without hacking up factory looms too much.....without the ignition relay the alternator obviously keeps the car running even if the battery is isolated. Has Damo or someone else knowledgeable got an idea?

BTW if I was doing a new car now I would just use 2 electric switches killing both legs of a relay (one +, one -). Easy to run the extra wires and no need to run full power all over the car. A switch like this would be appropriate for the external kill:



http://www.jaycar.com.au/productView.asp?ID=SP0786&form=CAT2&SUBCATID=978#1


Cheers Duncan. Good to know I didn't dream it up. Burgz man and byebye (Ian?) I'm more confused now, taa. Lol who would of thought it would be so hard. SO. I can't just do what you have Duncan, run the positive cable off the battery, up the a reachable spot, to a switch, then back to the fuse box thingy in the boot, then run the ignition wire out if the ecu loom, up to the switch, then back into the loom so I'm cutting battery & ignition? Will this stop th car. Also, thinking out loud, I'm not going to be turning the car off this way unless I'm stacked and or upside down. I'll only ever be pulling the switch while the car is off to stop the battery going flat, so worrying about alternator damage doesn't worry me as that will be the least of my issues if it needs to be pulled whilst running. Question is does the car stop with ignition wire cut and battery positive cable cut? Where does this resistor come in that comes with the FIA spec switch? Sorry if it all sounds retarded. I'm good at other stuff, I'm good at dents. And paint. But bad at wires

I did nowelsy 33. Was very easy and could be made to look stock. I will post up some details when I get half a minute.

I've also done r33 gtrs with electric isolation switches rather than the normal key type.

I did nowelsy 33. Was very easy and could be made to look stock. I will post up some details when I get half a minute.

I've also done r33 gtrs with electric isolation switches rather than the normal key type.

rightio, cheers. Appreciated
  • 2 weeks later...

Bit late in reply but if you're just after a switch to stop the battery dying, then switch the negative instead of running active wires thru the car.

Did that in my 33. No need for relays etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...