Jump to content
SAU Community

Recommended Posts

really need some help with this one guys.
I've been reading about and scouring the net for solutions but i cant seem to find anything that's fixed it yet.

Ive got an autech stagea (260 RS)
and whats happening is ill be driving along all good, and sometimes randomly, but usually after ive been coasting in gear for a bit then go to accelerate there will be either no response from the throttle of it will try to rev up and start sputtering like crazy and blowing out black smoke for about 2-3 seconds after which it will come back and run fine for the next few minutes till it happens again for 2- 3 seconds then runs fine straight after. Odd.

so far few things I've tried based on what I've found on the forums from similar problems are:
new fuel pump, replaced fuel reg, replaced CAS, replaced ignition pack, new splitfire coil packs + changed spark plugs as well as plugging in a consult cable to check for fault codes, there were none

I'm really running out of ideas here guys the car other wise runs fine and isn't down on power at all so im really just scratching my head over this one :/

one other thing i should add is today i pulled off the BOV's because i noticed just last week that i was getting a bit of fluttering, if say i put my foot down to full throttle (WOT) then back off to about half throttle it would flutter. (not sure if thats related to the sputtering at all)
I pulled them off and set them up for a bench test, and under 20 psi i was getting a lot of leakage out of the recirc outlet on both valves, within about 3 or 4 seconds the pressure in the piping dropped right to zero

checked everywhere else and there were no other leaks from anywhere else.... surely that's not right?


Link to comment
https://www.sau.com.au/forums/topic/429312-help-rb26-keeps-sputtering/
Share on other sites

ohh yea sorry forgot to add that as well

first i tried re soldering the connector pins to the PCB (a common problem there of having dry joints) which made no difference
so then i bought another pair to try and nothing...no difference

sounds like a good idea but wouldn't blocking them cause the car to stall every time i pull up, blocking them wont cause any other running problems than that will it??

fuel economy is as per normal but in regards to over fueling the only sign of running rich is the black smoke clouds i get when it sputters and some extra blackened spark plugs.

causes for over fueling?..... bad injectors maybe?


will have a shot at running around with them blocked though and see what happens
cheers.

BOVs need positive pressure in the signal port, the 6mm hose off the top, to remain closed and the. When that drops or goes to vacuum the valve opens

Fluttering as you described is normal for a GTR, both mine do it

Give it a full service, all fluids and filters, it's hard to guess the problem over the Internet

BOVs need positive pressure in the signal port, the 6mm hose off the top, to remain closed and the. When that drops or goes to vacuum the valve opens

Fluttering as you described is normal for a GTR, both mine do it

Give it a full service, all fluids and filters, it's hard to guess the problem over the Internet

yea i understand the concept of how they operate...just seemed odd that it was fluttering to me but if you reckon its normal then sweet...bit of peace of mind there, also seemed odd that when i set it up for a bench test with 20 PSI on both sides it was leaaking air out of the recirc outlet pretty quickly. went from 20 psi to 0 in about 4 seconds when i pulled stopped supplying air.

however....

update on the car.....seems to be sweet now

after i cleaned up the BOV's and absolutely drowned them in WD-40 it was still sputtering but after driving around for maybe 40 minutes it seemed to go away

been running fine for two days now cant believe it was as simple as that -_-

Well it turned out to be the bovs either not closing all the way or maybe the plunger not being able to move freely enough

literally all I did was take them out and hit them with some wd-40 and so far so good, will probably look into replacing them still though

hope that helps anyone else with any similar issues

yea i understand the concept of how they operate...just seemed odd that it was fluttering to me but if you reckon its normal then sweet...bit of peace of mind there, also seemed odd that when i set it up for a bench test with 20 PSI on both sides it was leaking air out of the recirc outlet pretty quickly. went from 20 psi to 0 in about 4 seconds when i pulled stopped supplying air.

however....

update on the car.....seems to be sweet now

after i cleaned up the BOV's and absolutely drowned them in WD-40 it was still sputtering but after driving around for maybe 40 minutes it seemed to go away

been running fine for two days now cant believe it was as simple as that -_-

I wasn't sure if that was how you did it as it wasn't stated and that isn't right they should hold that fine

if i get it right i can make them flutter for about 10 seconds, something i do when i'm bored driving around

good to see it's sorted, on to enjoying it

your not in western sydney area by chance, i saw a nice white 260 parked at the shops where we get coffees

yea exactly what i thought defiantly not meant to be doing that, ahh well ill pick up a pair of aftermarket replacements sometime next week just for the peace of mind that it wont come back, but do i really need to buy two, surely i cant just fit one and block the other off ?

hahaha i do the same thing about 10 seconds sometimes if im traveling up hill :thumbsup:
seems to be holding boost much better now than it used to though by the way

nah no where near man im from down in Melbourne, they're starting to pop up more commonly around here now though but everytime i see one its like.... http://i.qkme.me/3paixf.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
    • Thanks, will do that.  Thankfully they still feel great.
    • Yeah man, absolutely. You can try pushing me all the way in swapping the R34 for an E9x M3 
    • It's almost certainly going to be some amount of pads compound transfer onto the rotors. It will probably go away after you've run them for a bit. If not, pull it all out, lightly sand the rotors, scuff the pads, and rebed.
    • no one recommending speedtek gearsets?   i'm in the same boat as Cosline but rwd, I am holding boost back in third to 600nm at the hubs to save the gear as i make nearly 750nm at the hubs on a mainline
×
×
  • Create New...