Jump to content
SAU Community

Recommended Posts

Back to the story.

After finishing up at nats and having a mad time things went back to normal.

Just the usual things started with the car.

Removed my turbo timer and came across this mess.

Not sure who the hell did this home job but it all got removed and fixed.

lDHYqLh.jpg?1

After a few spirited runs through the cotter I noticed that my intake gasket was shot.

So I ordered a new one online and did some research on how to change it.

At the same time I decided to get rid of the hicas and chuck a lock bar in it.

The intake gasket is a farking bitch to change! cut the fark out of my knuckles, lost a spanner (still haven't found it lol)

If you ever have to change one then make sure you have ratchet spanners because they are awesome!

4pHq5jS.jpg?1

Well it only took me a week to do :P but Yeh, it's very tidy and works much better than it used too. Hopefully yours does too! Good job on pulling out the turbo timer too, I'm glad to be rid of mine. Should have listened to everyone that told me when I put it in, but I was all excited about having a turbo car :laugh:

Haha that's exactly what I was looking forward to when I purchased the car. Felt like a sick karnt walking away from the car while it idled for a while.

The novelty wore off within a few months and I couldn't turn the damn thing off otherwise the car wouldn't start. Home job wiring

Yehhh, mine stopped working. Wouldn't keep the engine running, but kept the electrics on for 30 seconds. Means my oil pressure gauge would scream at me when I shut the engine down at the pressure dropped below 20psi :laugh: So far no sign of my old starting issues either, so I'm hoping they were related to the turbo timer.

ANYWAY, got round to doing the throttle sealant yet?

It's been one day dude haha

Throttle body sealant will be done this weekend I hope.

I'm going to use some glue that I have here and make sure it's a really fine film so that it breaks when I open the throttle.

I will report back how this goes.

The proper sealant can be purchased but its $80 for a small tin

Fark that

Make sure that glue is oil resistant, you don't want blow-by breaking down the glue and having it fly into your motor :/ Personally I'd fork out for the correct stuff, $80 is cheaper than causing other problems...

Communal goo? - sounds like soggy SAO game !

but Robs onto something. I think there would be a number of locals who might need/use

or perhaps a shop like Trojan might part with enough to help you out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...