Jump to content
SAU Community

Recommended Posts

Back to the story.

After finishing up at nats and having a mad time things went back to normal.

Just the usual things started with the car.

Removed my turbo timer and came across this mess.

Not sure who the hell did this home job but it all got removed and fixed.

lDHYqLh.jpg?1

After a few spirited runs through the cotter I noticed that my intake gasket was shot.

So I ordered a new one online and did some research on how to change it.

At the same time I decided to get rid of the hicas and chuck a lock bar in it.

The intake gasket is a farking bitch to change! cut the fark out of my knuckles, lost a spanner (still haven't found it lol)

If you ever have to change one then make sure you have ratchet spanners because they are awesome!

4pHq5jS.jpg?1

Well it only took me a week to do :P but Yeh, it's very tidy and works much better than it used too. Hopefully yours does too! Good job on pulling out the turbo timer too, I'm glad to be rid of mine. Should have listened to everyone that told me when I put it in, but I was all excited about having a turbo car :laugh:

Haha that's exactly what I was looking forward to when I purchased the car. Felt like a sick karnt walking away from the car while it idled for a while.

The novelty wore off within a few months and I couldn't turn the damn thing off otherwise the car wouldn't start. Home job wiring

Yehhh, mine stopped working. Wouldn't keep the engine running, but kept the electrics on for 30 seconds. Means my oil pressure gauge would scream at me when I shut the engine down at the pressure dropped below 20psi :laugh: So far no sign of my old starting issues either, so I'm hoping they were related to the turbo timer.

ANYWAY, got round to doing the throttle sealant yet?

It's been one day dude haha

Throttle body sealant will be done this weekend I hope.

I'm going to use some glue that I have here and make sure it's a really fine film so that it breaks when I open the throttle.

I will report back how this goes.

The proper sealant can be purchased but its $80 for a small tin

Fark that

Make sure that glue is oil resistant, you don't want blow-by breaking down the glue and having it fly into your motor :/ Personally I'd fork out for the correct stuff, $80 is cheaper than causing other problems...

Communal goo? - sounds like soggy SAO game !

but Robs onto something. I think there would be a number of locals who might need/use

or perhaps a shop like Trojan might part with enough to help you out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...