Jump to content
SAU Community

Recommended Posts

You cant use jumper leads or a jump pack to start a car through a dead/dying battery.

Spark, Fuel, Oxygen (not necesseraly in order)

When you go away you disconnect ignitor and AFM. It's not the first time you have done this.

This time you reconnected Ignitor and AFM (as per every other time). Today it started, idled and then stalled in gear. when you went to leave.

Was it difficult to start or sound unfamiliar ?

Leads me to believe Fuel or Spark. You say the tank is full.

Can you here the Fuel pump prime ? Is there fuel getting to the rail and reg ?

based on the response either the FP is dead or there is not enough power to the pump.

You have Fuel pumping through its veins - Y/N

(Some times you can hit the tank from underneath near your fuel pump and it will work again till next failure)

So moving onto spark

Check again your ignitor and AFM plugs. Dry, good connection ?

You car should still start with your AFM disconnected.

Ignitor - a possibility. But put that on hold for now.

Starter - possibility but these generally wear out (you would know it's coming)

Put a mates battery in - known working. Try turn it over.

Still not working ?

When was the last time you changed/checked your plugs. They can oil up and it's a bitch to start.

Oh and being a manual (no pun intended) this morning you could have tried jump starting down the road.

This can remove a few items off the check list (Alternator, Starter Motor, Battery) to get your car going.

Do anything else before you parked it ?

Edit: Both sides of the ignitor plugged in, is it earthed properly ?

Edited by Sinista32

I disconnect them every time I go away for a weekend. (Heads up to the robbers lol)

The car started the same as it has every day and didn't seem any different.

The only difference was a slightly different note to the idle, however it was sitting fine at 1000rpm

The car rolled as I clutched out and gave it a little revs, about half a meter and this is when it stalled.

I can hear the pump prime and stop like normal so that leads me to believe it would have fuel pressure?

I will have to check about if the fuel is pumping correctly.

Where should I be checking this? My thought is to disconnect the line just after the fuel filter.

The plugs were changed about 10,000km ago and I checked them about 1,000km ago when doing a compression test

(All looked fine bar 1 that had a little oil due to a leaking cam cover gasket, this has been ordered and will be replaced)

I cleaned all the oil from around the area to make sure it does not happen any time soon.

I was worried about attempting a hill start and not being able to get it home if this fails due to the hills in my area.

The car was running fine when I parked it on Friday night.

Edit: No immobiliser and plugs are both plugged in (Heads up to the robbers again lol, I have a shotgun)

dude i can come around with my battery and we can test it out or if that doesnt work atleast two minds will be better than one especially when your almost freaking out you might not be thinking straight could be a very small problem.

it could also be the issue you had with the sealant fr the TB somehow not opening up to let air in. Because you said it started then stalled could be the TB is stuck on the close position. Try starting with your foot down to the pedal a little just enough to open it.

Verms has said he might come around as well.

3 minds are better than one manual haha

Bryce you are more than welcome but don't you live on the North Side?

nah i live in the dirty south. Pretty sure i still remember where you live haha. Been stalking you lately

Not that this is your problem but just to put it out there... If your Battery is too flat, you cannot roll start it.

Check to make sure that little Indian Boy hasn't lost his ball inside your Enginebay somewhere. :laugh:

post-78856-0-51127000-1376899055_thumb.jpg

Okay so the car is still sitting in the driveway and isn't starting.

Bryce came around with tools and Shane (Wilderboy)

-checked the return fuel line and it sprayed fuel everywhere so I checked fuel off the list.

-triple checked the plugs and they were all secure.

-pulled out the spark plugs and they all had fuel on them but no oil.

-plug the spark plugs into the coil packs and check if they had spark, all of them did.

-put it all back together and tried to start it.

No luck it just sits there turning over but not starting.

The ignitor pack on top of cam cover does have a crack through it but the spark plugs had spark..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...