Jump to content
SAU Community

Recommended Posts

Heey i bougt a Bee-r from a well known trader here but i think it looks different then the regular bee-r limiters on pictures.

First thing what looks different is where the cables are coming out second is the cable which looks thinner

What do you guys think? Already mailed bee-r but they arent responding.

post-105921-0-48938500-1377863956_thumb.jpg

post-105921-0-43477700-1377863979_thumb.jpg

post-105921-0-78052300-1377863999_thumb.jpg

post-105921-0-88923300-1377864012_thumb.jpg

Edited by f5twister
Link to comment
https://www.sau.com.au/forums/topic/431079-is-this-bee-r-revlimitter-fake/
Share on other sites

from the pics it def looks like a knock off. Way different to mine.

1. Those loop lines are way too long

2. no heat shrink on those loop lines

just as a start but thats just my opinion. I got mine directly from jap land but not aware of any changes to the model.

see attached

post-2127-0-87900400-1377898635_thumb.jpg

Lol doesnt harm engine as much as stock limiter as long as gain isnt on the big bangs and overuse it

But please stay ontopic

So what's the point in having it?

Use your foot and brain and buy something useful for your car.

Total waste of money!

So what's the point in having it?

Use your foot and brain and buy something useful for your car.

Total waste of money!

Agreed

It all looks the same as some photos on google...

bee-r-racing-rev-limiter-model-30175-2-l

And it also looks like there are slight changes between them.

so youre saying that everyone with launchcontrol is a ricer and wants to get noticed ?

First of all these limiters are safer for a engine you can install les revss and you have no fuell cutt duo to cutting the spark signal,

thats why unburnt fuel detonates in the elbow, but as i said it would be fine if you dont turn gain up to high which some people do because they like they bang bang indeed and yes high gain and overuse can damage the engine but i said that my plans where not to use a high gain, so please stop bashing the limiter now and my choice to buy one its my car and my money Mkay?

Edited by f5twister
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are black hose clamps as well if you care. Plazmaman for example sells some: https://plazmaman.com/product/black-hose-clamps-premium-quality-stainless-breeze/
    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
×
×
  • Create New...