Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Night all. Hopefully get the leopard back from the auto elecies tomorrow so we can rip it apart and fix it all up for Martin

I'll tell you what. The boss is giving this one the treatment, noting everything and even things it didn't come in for :P

I think imports are growing on him hahahh time will tell

How's this. The auto shop guy walks in looks underneath at the auto and the bottom of the engine for 20 seconds and says vg30, same gear as a z32

Night all. Hopefully get the leopard back from the auto elecies tomorrow so we can rip it apart and fix it all up for Martin

I'll tell you what. The boss is giving this one the treatment, noting everything and even things it didn't come in for :P

I think imports are growing on him hahahh time will tell

How's this. The auto shop guy walks in looks underneath at the auto and the bottom of the engine for 20 seconds and says vg30, same gear as a z32

sounds like he is good at what he does then

Yes well, where were u two years ago Chantelle! Wahhhh :(

I was living in Bendigo with a 2 year old and an idiot, cruising in my Skyline and working my butt off at Uni

Night all. Hopefully get the leopard back from the auto elecies tomorrow so we can rip it apart and fix it all up for Martin

I'll tell you what. The boss is giving this one the treatment, noting everything and even things it didn't come in for :P

I think imports are growing on him hahahh time will tell

How's this. The auto shop guy walks in looks underneath at the auto and the bottom of the engine for 20 seconds and says vg30, same gear as a z32

No. No. Not same gear as z32. Z32 is TT this is T. Also, the racks are very different.

Spoke with Richo yesterday about the build. Long story short, falling a few days behind firs estimate due to new 2000cc injectors being too tall and fouling on the plenum. Re ordered some smaller ones to suit. Downgraded to 1200's, not ideal but still more than big enough for what the rest of the car will be able to handle at this stage. I think i wil go through gearbox & diff before I need bigger injectors

You are correct Andy, I'm at the "Not really bothered stage" in regards to time its taking to be ready. I was more annoyed about not being able to stick with the injector size I preferred. Richo said the Dump/screamer setup is awesome though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
    • street use or race track, what hose size and why? what factors change with the hose size options ?   see most comon is an10. when you see most oem external coolers are closer to an12? does high volume oil pump like nitto need an12 or 10 be just fine
    • The rod I was moving left and right you can see looking from the passenger side floor up into the center console.  IMG_8095.mov
×
×
  • Create New...