Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Morning mate

Sounds like a good plan

Igniter is in the coils, does not look like loom or coils TBH they operate under load and at speed, not plugs either.

Background on the car:

400rwhp r34 gtt

never had an issue with missfire ever

109000K's

only missing at revs while free revving

no issues under load or at max boost (23psi)

Igniter should be a separate unit consisting of transistors/diodes. they are on the back of the rocker cover on rb26s - not sure where located on r34gtt. They are also referred to as a Power Transistor Unit

I believe that in s2 Rb25's and neos, the ignitor is inside the coilpack. Unlike the s1 Rb25. I'm not familiar with 26 setups though

RB26's have their igniter module at the back on top of the plug covers.

rb25s - Answered

MagicMikeZ32 would know all about them failing lol

Mine were 20+ years old, no issues. Don't even need engine out to change them.

Having said that, I am using yellow jackets at the mo, for no aparant reason other than 'modify'

Mine were 20+ years old, no issues. Don't even need engine out to change them.

Having said that, I am using yellow jackets at the mo, for no aparant reason other than 'modify'

Not the coils the PTU in Z32s. I had to replace mine. http://forums.nicoclub.com/tip-for-ptu-problems-t276337.html

http://tech.aus300zx.com/ignition/ignition.htm

I believe that in s2 Rb25's and neos, the ignitor is inside the coilpack. Unlike the s1 Rb25. I'm not familiar with 26 setups though

So thats the difference between S1 and S2 packs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...