Jump to content
SAU Community

Exedy Vs Rpm Clutches - Any Real Difference?

eightsixboy
 Share

Recommended Posts

eightsixboy Mentor

eightsixboy

Posted
Posted

Hi all,

I need a new HD clutch soon and have noticed that the Exedy ones are about $150-200 more then the RPM equivalent.

Is it worth it to spend the extra on the Exedy or is there really no difference?

I basically just need a clutch that can handle up to 230rwkw so hoping that either HD will be ok.

Thanks.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

DO NOT get the Exedy Heavy Duty Range, the pink pressure plates, they're rubbish.. make sure it's the silver cover which is made in Japan.. not a remanufactured OEM item that is sprayed pink.

I bought my car with an RPM clutch and it was slipping hard (due to uneven wear) so I removed the clutch kit and replaced it (my only experience).

Blackkers Experienced

Blackkers

Posted
Posted

I've got an excedy heavy duty, I don't know which model but when I did the engine swap and moved the clutch over it was about 75% worn (hard to tell) and the pressure plate is pink. I just tuned up to 240rwkw and it doesn't just bite any more theres a split second of slip. 3rd gear won't stall the motor any more, if I let it out in 3rd on boost it will just slip.

Is my clutch on the way out? I'm going for 300rwkw at the end of this year, not sure whether to do it first. Lots of people say over 300 is fine with this clutch but i'm not convinced

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

Blackkers, chuck it into 4th gear and boost up a hill. You will either notice it slip or it won't slip and that's how I would determine.

My pink excedy lasted a few power runs on the dyno before giving up on the way home on the highway. This was 250rwkw

I am currently running a KB clutch from KB clutches in Sydney. Great service and amazing price, just call him and send him a dyno sheet or some specs of the car and he will do the rest

Blackkers Experienced

Blackkers

Posted
Posted (edited)

Okay mate I'll definitely give it a go. I know the clutch has a bit of meat on it i'm just not sure how it will handle the power i'm chasing. Thanks for your input

KB seems to be the place for clutches too

Edited by Blackkers
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Got the RPM in the end, haven't fitted it yet but it looks pretty decent.

Honestly couldn't justify spending almost double on an exedy.

Good luck mate, hope they have revised their clutches. They had a bad run for a while, and I was one to suffer from it.

donburtron Enthusiast

donburtron

Posted
Posted

It depends on where u buy the clutch from i guess

i bought a new hd exedy clutch and gtr racing flywheel for 925 shipped to my door and it only took one day.

call this number and ask for simon and tell him josh from armidale gave u his number 0296481688

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Neil's R33 Gts-t Build

      By The Bogan · Posted

      It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • perry_r33
      Skyline R33 Sedan Tail Lights S2 - (2 SETS Available) Silver & Grey

      By perry_r33 · Posted

      Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...