Jump to content
SAU Community

Recommended Posts

My car is a 1.5, engine has bits from S1 and S2 but more S2..

No problems so far and i think fuel economy has remained the same.

Didn't want to hear that last bit T^T

Filled up again, 10L per 100km but was $1.71 today.

Well considering my latest fuel economy was 13.99L/100kms and that was $1.69 when i filled it up, in saying so there was a mountain run involved in that tank of fuel. pulled 356kms out of 49.71L that was on V-Powah

Well considering my latest fuel economy was 13.99L/100kms and that was $1.69 when i filled it up, in saying so there was a mountain run involved in that tank of fuel. pulled 356kms out of 49.71L that was on V-Powah

I'll drive this tank really low and see my fuel economy on P100 but I'll fill up with v power and see if my economy gets worse or stays the same.

At the moment I'm not sure if it's the fuel or the brand new CAS that I installed 2 weeks before I started using this different fuel.

I'll drive this tank really low and see my fuel economy on P100 but I'll fill up with v power and see if my economy gets worse or stays the same.

At the moment I'm not sure if it's the fuel or the brand new CAS that I installed 2 weeks before I started using this different fuel.

True, I'm half wondering if my new high flow cat is causeing the jump in fuel useage.

Btw this P100 fuel has up to 10% Ethanol added not 5%.

I'm keen to install my PowerFC again, will be a good way to monitor knock BUT saying that I haven't felt the standard ECU reduce power entering the knock maps....

Just do it Zeke. The poor old Ark is on deaths door but even she runs well on it.

P100 = No engine light, better economy, not running rough

Shell or BP= carries on like the ark

  • 4 weeks later...

Car had P100 for happy laps and is going great :D

Did 13L per 100 km from home to happy laps and back.

If I had the money I would get the car tuned on this fuel with the PFC I have sitting around.

13L:100kms :( better then mine. But you've heard what's going on my end with fuel. I'm getting just under 14L:100kms

I've run P100 in my R34 for about 6 months and had it tuned on it, power went up from 200rwkw to 217.8, not a bad increase seeing as nothing else changed. I generally get between 500-550kms on a tank but that's almost all highway driving. Definitely gives the car more power down low I've noticed too, never going back to 98

Should be perfectly fine, but a good precaution is to change the fuel filter after the first or 2nd tank. This is because ethanol can dissolve some of the gunk built up in the system.

The extra fuel usage would only be 2-3% on closed loop, and essentially nothing on open loop unless you re-tune it slightly. The ethanol content should help in hot weather as a bit of ethanol both boosts octane and broadens the optimum optimum timing point.

I wonder if it is only 100 octane, or 101-102 ?

Should be perfectly fine, but a good precaution is to change the fuel filter after the first or 2nd tank. This is because ethanol can dissolve some of the gunk built up in the system.

The extra fuel usage would only be 2-3% on closed loop, and essentially nothing on open loop unless you re-tune it slightly. The ethanol content should help in hot weather as a bit of ethanol both boosts octane and broadens the optimum optimum timing point.

I wonder if it is only 100 octane, or 101-102 ?

There's reason to believe that it can fluctuate because of how the ethanol reacts. Could be higher, could be lower. From memory, I think that it's a minimum of 100 octane.

Also, you mum. Hehehehe (reference to your signature)

Never tested it, would be interesting to see. The performance difference is considerable, I went back to 98 this week and the car feels like crap.

This would equate to the ethanol burning more efficiently and assisting with the combustion of the petrol. Whilst it's small in what it does, with a car like yours, the change in feel would be remarkable however the actual numbers wouldn't change to much. Also, ethanol would assist with better, cleaner det - important especially on yours.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...