Jump to content
SAU Community

Recommended Posts

Hi Guys

Can anyone shed some like for me on the late 98 Series 2 RB25det Stagea RS-Four? Brought one being told it was a Neo. Picked it up started stripping it off to put it in my S13. The Cas is the Black plastic cas, the loom is the grey plug ecu. I thought it was a Neo from that, but further looking into it it had the side feed injectors, the 3 bolt IAC valve, the small TB. Which had me instantly suspicious about it being a Neo.

Looking around found 2 pictures of Late model RS4's with these motors. Does anyone else know anything more about them?

http://www.autospeed.com/cms/article.html?&A=2529

http://www.skylinesaustralia.com/forums/topic/368359-syd-nissan-stagea-rs4-dayz-edition-wgnc34-pearl-white-rb25det-awd-no-sunroof/

My guess is a Series 2 motor internally and intake and exhaust sides. But whats the deal with the ecu now? would i use the R34 GTT pinout for the grey plug ECU?

Just wanting to know this as i plan on hard wiring the motor to the battery via a switch and fuse panel.

Link to comment
https://www.sau.com.au/forums/topic/433161-late-series-2-rb25det/
Share on other sites

Both the stagea's in the pictures are s1 stagea's so they have s2 rb25det not the neo model , s2 stages 98 onwards "the ones with the spot lights in the grill have neo engines , the s1 computer is untuneable unless you run a stand alone or piggy back system , you could change the cas and comp over to a neo one , then you could run nisstune , but I'd say ATM you've just got a s2 rb25det

sorry i must or worded myself wrong. i've worked out its a S2 rb25det from a S1 Stagea. Is it common for these to have a grey plug and not the normal blue plug like the R33 RB25det's? Do they share the auto trans ecu in there?

I'm not planning on tuning this motor any time soon, will be left as it is just in a track hack S13. I just want a ecu pin out i can figure out how im going to rewire the loom up to power and switches.

is this the pin out i want, from this post here, http://www.skylinesaustralia.com/forums/topic/406866-ecu-tuning-for-s1-stagea-do-we-have-a-solution-yet/?p=6516626

Yes that will do it. if you are running it with a manual box you can always swap it for a plug in Link later.

sorry i must or worded myself wrong. i've worked out its a S2 rb25det from a S1 Stagea. Is it common for these to have a grey plug and not the normal blue plug like the R33 RB25det's? Do they share the auto trans ecu in there?

I'm not planning on tuning this motor any time soon, will be left as it is just in a track hack S13. I just want a ecu pin out i can figure out how im going to rewire the loom up to power and switches.

is this the pin out i want, from this post here, http://www.skylinesaustralia.com/forums/topic/406866-ecu-tuning-for-s1-stagea-do-we-have-a-solution-yet/?p=6516626

Yes Link make plug in ecus for Nissans, evos, Toyotas etc. They also make a wire in version which can be adapted to almost anything. I have a G4 plug in (the R34 version to suit the Stagea plug since I have a manual conversion). I think the only mod necessary was a wire from the TPS to enable the Atessa ( I didn't install it - the tuner did).

Didn't think links where full plug in ???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...