Jump to content
SAU Community

Sau Qld December Club Meeting, Wednesday 4Th Of December


Recommended Posts

Hey all,

The monthly meeting for December is coming up this wednesday. These monthly meetings gives us a perfect opportunity to cover the basic house keeping of the club, recap on past events and let you know about the exciting upcoming events. It also means we get to have a good feed!


Event: Sau Qld Monthly Club Meeting

Location: Vroom Bistro and Bar

1/46 James Street
Fortitude Valley

There is plenty of off street parking.

VroomMap_zps788aca1e.jpg

Date: Wednesday, 4th of December

Time: 7.00pm onwards

Cost: Main meal prices are from $19-$32. As Vroom is a Club supporter, you will receive a 10% discount when a current membership card is presented.


Requirements: This is an Open event, so you do not need to be a member to attend as everyone is welcome.

We ask that attendees obey all Road rules.
We don't want people racing up and down the street or general Hooning.

Remember you are representing the Club, so we need to be on our best behaviour.


See you all there!

How are the polos guys?

Haven't tried mine on yet.

Oh shit this was tonight ..........

car still in at NextUp anyway sorry guys will try make the next one.

All good, Vroom ended up being closed last night for some reason :/ so we ended up hiking it for 10mins to Grilld.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...