Jump to content
SAU Community

Recommended Posts

Before:- My EVO had a few scratches here and there + particulate matter + swirl marks despite a Grade 4.5 in Osaka

This is how the car appeared before Eugene got to it on a Sat morning.

P1050298_zpsba8cbcd1.jpg

After:- By Sun afternoon after being picked up from Hornsby Station, my car looked like this...

Terry-45_zps8012ad2c.jpg

Terry-44_zpsb04814c6.jpg

Terry-46_zpsdd1038dd.jpg

History:- Eugene has had many wraps before with cars that he's detailed in HPI, Zoom and PG magazines; but personally, he did wonders with a car that was Grade 3.5 > Best Concours at the R34 GT-R 10th Anniversay and Daily Telegraph Cover Story.

Before:- Eugene knew he had a job and a half, to do with this...

R34Aug08010.jpg

After:- And it ended up like this...

God_speed-17.jpg

Eugene is available to anyone in the Sydney area on 0421141538 but it's best to book well ahead.

Thanks Eug.

Link to comment
https://www.sau.com.au/forums/topic/435825-eugene-chans-work/
Share on other sites

Yep, Eugene does/did some work for the dealership that I bought my stagea from.

Needless to say it was very well presented when I bought it, and has made subsequent detailing of the car easier.

+1 for Eugene.

Yes that's him Nick.

One thing I found fascinating about Eugene's attention to detail is the way he goes over all metal panels with his paint thickness gauge to see...

a) if there's been panel repair and

b) how much paint he has to work with.

On the Bayside Blue GT-R, there was a consistent 320 microns.

EugeneDetail14.jpg

On the Pearl Black GT-R, there was a consistent 180 microns.

R34GTR102_zps834ffef2.jpg

On the Mica Grey EVO, there was a consistent 120 microns except for the front left guard which was about 200.

The omission of any repair on the LF on the auction sheet I guess, is something to consider about Grade Validity.

Terry-48_zps14612286.jpg

On the Polar White N1, Eugene only had about 80 microns to play with - *gulp

Polish was devoid of cutting compund.

Eugene-14.jpg

It could have been so easy to cut through the paint...

  • Like 1

Actually, there is far less to play with as a detailer.

The tool measures the whole thickness, where a detailer is essentially working with just the clear coat layer to produce results. The clear coat layer is thin compared to the paint thickness.

I too went over the stagea with a thickness gauge, finding a clean straight car :) The roof and bonnet were however notably thinner than the other body panels.

The goal is to take off the least amount possible. But as far as I know even a fairly aggressive buff will only take off about 10 microns, however, its not something you want to do every 6 months... Sometimes better to leave some swirls behind.

  • 1 month later...
  • 1 month later...
  • 4 months later...
  • 2 weeks later...
  • 5 months later...

Being detailed as we speak. Eugene's final task before Christmas.

A "Before" shot...

but Eugene can show just how dirty this was.

Terry-116_zps24fb10f5.jpg

V-Spec II N1

* Eugene has kept abreast of new processes - a sign of a professional who refuses to stop adding to his wealth of knowledge

* New cleaning agents

* New polishes to match is array of pads

* A choice of post-polish coatings

a) quality sealant and quality wax or...

b) ceramic coating - yes at extra expense. But that's best to discuss with the expert.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...