Jump to content
SAU Community

Recommended Posts

Hi all. I bought the car back in September. Had all the maintenance done that it required etc etc. Part of the work done included new belts as they hadnt ever been done. Yesterday two out of three belts came off. I checked the belts, they all have the same markings on them, so either they were all replaced or none of them were. My receipts states that they were.

Extent of damage thus far is not known apart from what I can see.

Belt for the alternator is gone

Belt for the thermo fan is also gone

When the belt for the fan came off, the fan came loose, sheared off from everything. In doing so it has sliced at least one radiator hose and taken out the radiator completely.

The last belt is still on. To the best of my knowledge this all took place in my driveway when moving the car. So damage may be minimal? I have no idea.

Given that I have an invoice to the tune of $1500 that included new belts, they should last a lot longer than six or seven thousand km's. So who is at fault here? Belts are supposed to be good for around the 100k mark, maybe a tad less depending on car and application.

There is a fair chunk of work here and I genuinely dont see how any of this up and coming repair bill is mine in any way shape or form. If this were your problem, how would you go about it? Obviously i have to contact my mechanic and tell him whats happened at some point and see how they feel about it.

What are your thoughts? What would you do?

In the first instance contact the shop that did the work as soon as possible.

Could be tricky as they may be closed for Christmas.

Do they belong to a trade association to which you can complain if necessary?

Make some enquiries about the relevant consumer protection laws so you can quote them if necessary.

In this country the last resort would be the small claims court/ disputes tribunal

But try the direct approach first and be calm and polite but insistent!

Damage is likely to be limited to what you have observed unless the cambelt has also gone - which is unlikely.

This exact thing happened to the 25G. The fan/waterpump belt was overtightened. The water pump shaft sheared. The fan had a whirling orgasm under the bonnet.

New radiator, new (VL) water pump, new belts.

Call the shop first thing for sure. The belt could have been over tightened putting big pressure on water pump and if the fan bolts were left loose then it would do 2 hat you are saying for sure. They are at fault

Hey all. Thanks for the responses. As you can see I am no mechanic and have only mentioned what I can see. So, from what I have described, no internal damage to the engine then?

Yep, wrong time of year. I will give them a call tomorrow and see what happens.

Hey all. Thanks for the responses. As you can see I am no mechanic and have only mentioned what I can see. So, from what I have described, no internal damage to the engine then?

Yep, wrong time of year. I will give them a call tomorrow and see what happens.

No internal damage, so don't stress.

Let us know how you go!

Belts only cost about $30 - if there is no other damage I wouldn't bother arguing with them - if your located in western Sydney I'd be more than happy to refit them for free for ya...

Problem is these dodgy mechanics always find a reason to not be liable for their f**k ups!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...