Jump to content
SAU Community

R33 Gtst Clutch / Gearbox Info Needed

Stealthynsa
 Share

Recommended Posts

Stealthynsa Proficient

Stealthynsa

Posted
Posted

Hey guys my car is running now and good to go but after unbolting the clutch hydraulic thingy lol that pushing the lever on the gearbox to open the clutch itself I can't get it back in place to do up the 2 bolts.

So right now IDE love to go for a drive but I can't as I can engage the clutch without it bolted up, is there a certain way you need to go about it to be able to do so because it's to long to fit back in and bolt up? Thanks

Link to comment
https://www.sau.com.au/forums/topic/437004-r33-gtst-clutch-gearbox-info-needed/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

It may have jammed. Mine did this not long ago

If so take it to a brake shop and get them to re-kit it or sleeve it if its to far gone

Should be able to push the internals out and give the inside a light sand if its not to bad. Then if the seal is still ok you should be right to re-use it

89CAL Grand Master

89CAL

Posted
Posted

If it has just light rust its fine to clean it up a bit. Honing it with a small hone would be best if you wanted to go buy one

Mine just had light surface rust near the end where the piston was not running. I gave it a light cleanup and it probably would have been OK to run again but decided to go get it refurbed.

They can be reconditioned alot cheaper then buying a new one so no need to throw it in the bin unless its completely f**ked. They can re-sleeve it anyway. Mine was going to be sleeved for $50 but turned out it was fine for just a hone, even after id cleaned it up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The alloy coolant reservoir has a sight glass, so as long as I can see coolant in the sight glass it's GTG, as for PS, it isn't anything catastrophic if it gets low, and as it hasn't lost a drop since I have owned the car I cannot see it being an issue, even after putting the "big block" 2.5 in....LOL The only time it gets slightly messy is at oil changes, as the oil filter sits above the frame, and I need to use a plastic bottle with its bottom cut off to catch the flow when loosening the filter
    • Duncan
      Single Turbo Conversion On R32 GTR.

      By Duncan · Posted

      Good on you for taking on the job, but it is a big one. Even if you have bolt on manifold and turbo, you will need: Post throttle pressure source to boost controller to wastegate (and FPR, and ECU/MAP sensor) Pre throttle pressure source to top of BOV(s) Oil feed - you can take that from the standard port in the middle of the block Oil return to block under the turbo - this is much trickier than it seems to route a decent/wide pipe past the manifold. You really can't use rubber hose because it is way too hot there, and also the oil out of the turbo core is a bit frothy so it needs to have a decent diameter Water feed - you can take that from the standard port in the rear of the block. Water return - mine runs to a T into the heater box return, just make sure you don't create a high point making bleeding hard. All of those lines should use 200 series style teflon braided hose with heat shielding because everything needs to be routed past the manifold. Also a turbo beanie is a really good idea to minimise the chance of the car catching fire (under bonnet lining in particular) You also need to decide a cam cover breathing solution as well, will you vent externally via a catch can (probably illegal) or return to the intake (plumbing required and can oil up everything over time) Keep in mind the intake and exhaust piping in the engine bay will be custom so you either need to be able to fab ally and steel or have someone you can get a car that isn't running to. Get the wideband fitting welded into the dump pipe at the same time. Also, just my opinion, a screamer pipe attracts attention and doesn't add power, I'd plumb it back if you want to be allowed to keep the car on the road. BTW do you know anything about how healthy the motor is, and what power you are targeting? Doubling or tripling the factory power on an unknown motor is a little risky. Also fuel system will need some attention (pumps, high current hanger, direct power and earth feed, injectors etc)
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Wrinkle black will be a thing for both
    • shubby0901
      Living With An R33 Gtst

      By shubby0901 · Posted

      As I wait for parts to be delivered, I have managed to procure via a contact a R32 Nistune ECU......for now I just want to monitor what the car is doing but eventually.......who knows where we go 😂
    • MBS206
      NC MX5

      By MBS206 · Posted

      To back this up, I'm always looking on the outside, seeing the level, and then opening it up anyway, as I'm worried the level I've looked at, is more so a scunge line. Then you end up dipping your damn finger in it too depending on the type of tank you're looking at just to make sure I'm not going insane.   PS, Mark, polish up the none moroso one a bit and then give it a clear coat. The Moroso one looks to be way shiner (not mirror polished, just shinier) and it'll still look weird with the two different alloys beside each other. Either that, or Id probably paint them a flat black...
×
×
  • Create New...