Jump to content
SAU Community

R32 PFC alternatives

JH32

By JH32,
in Forced Induction Performance

 Share

Recommended Posts

JH32 Grand Master

JH32

Posted
Posted

Now I know that you can't get an R32 Power FC, but since I'm a bit of a pleb I don't know what the alternatives are.

What else have people used that is good?

How about LINK?

Link to comment
Share on other sites
adam 32 Grand Master

adam 32

Posted
Posted

you can get a power FC apparently

but hard to come by and expensive

anyway with a remappable ECU why replace it?? just go see lumpy at c-red! i guess if youre after BIG power then a motec or seomthing but realistically a rempa should sort you out

Link to comment
Share on other sites
Guest Zoobie

Guest Zoobie

Posted
Posted

What about WOLF 3D? Plug in ECU's are already happening for the R33....I had my R32 running on one yesterday thanks to Nissan keeping most of the electricals the same.

Cheers,

Zoobie

Link to comment
Share on other sites
Joe Community Regular

Joe

Posted
Posted

if i was you i would go for a motec i heard there a model for a plug & play r33 gtst & a r32 can be done if asked & it also allows you to remove the Air Flow Meters, so you can just run a massive pipe stright to your new after market turbo ;)

I brought me a Power FC for my r32 gtst (HCR32) it was hard to come by but if u try hard enough u will find it.

*NOTE* HCR32 Power FC was made on demand by AP Engineering (APEXi Engineering) it was never a item you can find on the apexi catalogue, i beleived it was a remapped r33 or a r32 gtr Power FC unit to suit the R32 GTST (HCR32).

If you cant find the Power FC or your not willing to go for the motec it the better option.

If you would like to search for the power fc the part number is

Skyline HCR32 RB20DET 89/5 - 93/7 118,000 4E14N07Z Only MT

Thank Meggela for the part number.

Hope this helps.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chris_Guthrie
      Misfire/stalling issues

      By Chris_Guthrie · Posted

      Any recommendations on a decent replacement manifold that doesnt break the bank or require additional mods for the stock turbo setup? I figure if I'm going to pull the manifold off anyway to fix the studs might as well replace it. 
    • Chris_Guthrie
      Misfire/stalling issues

      By Chris_Guthrie · Posted

      So I checked the turbo out today. Very minimum play at all just enough for the oil to take up when it's running. I did find an exhaust leak at the manifold. 1 stud all the way in the front is missing and the one all the way in the back is broken off. Front has visible signs of an exhaust leak. I'll fix that soon but that's not my problem still.  I also found that the nipple coming off the turbo had the hose capped off and a hose ran from the j-pipe by the bov going to the wastegate. I removed that hose and capped that nipple and put the turbo nipple hose back on the wastegate.  There was a ton of oil residue all through the charge side of the intercooler piping going to the throttle bodg. I'm thinking that's from the pcv. Doesn't seem to be coming from the turbo that was all clean on the pipes side.  Haven't had a chance to check fuel pressure yet, haven't had time been having to pull a lot of doubles at work. I did pick up some carb cleaner to clean the iacv but wanted to make sure I had a fresh gasket in case the old one rips when I pull it off.  I'm waiting on a MAF that was supposed to be here today but delayed to Monday. Have a double Monday and Friday and work all of next weekend so going to try to find some time in the middle of the week to try that out. Did about a 10m trip around the block today and towards the end the issues were coming back. Fingers crossed on this MAF but if not just going to throw a fuel pressure gauge in and see where I'm at.  Did notice today that I can definitely hear the injectors pulsing. Very audible clicking coming from them. Assuming that's normal? Should also mean CAS is functioning somewhat properly. After it warmed up when I started it the intermittent misfires came in again. Did start doing that before it was fully warmed up. 
    • klutched
      GOT SUM's RB34

      By klutched · Posted

      This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • Dose Pipe Sutututu
      Rear suspension upgrades

      By Dose Pipe Sutututu · Posted

      A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
×
×
  • Create New...