Jump to content
SAU Community

WSID street meet wed night 30th june

bbenny

By bbenny,
in Events Archive

 Share

Recommended Posts

  • Replies 110
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Majanal Grand Master

Majanal

Posted
Posted

bbenny, not I sorry mate, have to work unfortunatly.

R33vit, I was told to give my clutch 500-1000kms before giving it a pisling, apparently they are a little like breaks, you need to bed them in to get maximum efficientcy out of them. :)

R33vit Experienced

R33vit

Posted
Posted
R33vit, I was told to give my clutch 500-1000kms before giving it a pisling, apparently they are a little like breaks, you need to bed them in to get maximum efficientcy out of them. :D

As it turned out I didnt run on Wednesday nite...

Should be ok for next week tho

2rismo Grand Master

2rismo

Posted
Posted

JAS, was talking to Scott today at work. We should cruise up in the early arvo to WSID and lay the Gong Smack Down on the place!!

If only you were in W.A. mate. Your stocker could run 10's !!! :D

Adrian

 Share
Go to topic listing


  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
×
×
  • Create New...