Jump to content
SAU Community

Recommended Posts

I'm about to replace my back left wheel bearing for the 3rd time in 6 months, and I have a few questions -

1st time - whole hub/bearing purchased from a wrecker, which was discovered to have play in it once I put it all back together. Lesson learn't - don't buy second hand bearings!

2nd time - brand new bearing, which I had my workshop remove the old hub and press the hub into the new bearing. Anyhow, had it wheel aligned last week and they said the back left bearing was stuffed.

So I spoke with the bearing company, and they said I can give them the old bearing and they can lodge a warranty claim. They mentioned that it may not have been pressed in correctly and may have been damaged during this process, or my installation has caused the failure.

This will be difficult at best, as the old one was destroyed removing it from the hub the second time around...

I've ordered another one and pick it up tomorrow, so hopefully I can change it all out tomorrow with any luck. I did a DIY post the second time around - http://www.skylinesaustralia.com/forums/topic/434655-r34-gtt-rear-wheel-bearing-replacement/

I can't see anything I've done wrong in the installation? Could it be I've just got a dud bearing or its been damaged when the hub was pressed into the new one?

Sounds like you had a bad run. I have installed heaps of wheel bearings into Stageas, never had an issue myself. Perhaps the hub was damaged to begin with?

I assume they pressed the inner race, not the outer, that would kill the bearing instantly.

Yeah I remember trying to find a socket that fit nicely on the inner race when they had it on the press, so I'm sure it was pressed with the inner race being supported.

One question - is there supposed to be a washer or anything in between the bearing and the nut that screws onto the driveshaft?

I did a similar boo boo to you. I replaced my control arms with used ones, paid $450 for the lot and lesson learned never go second hand they are worse than mine.

The fact yours keeps breaking so early may be because you have some additional stress on the bearing thats wearing it out way too fast. Make sure all other suspension components are in proper order and aligned correctly, and use only genuine nissan bearings.

By the way is there a guide to change the FRONT bearings on a GTS-T? The rear bearings are piss easy but the front look crazy hard. I would appreciate that.

Edited by sonicz

Nope, but that part has little to do with the bearing, it just stops the shaft from slopping around, and the bearing from sliding off the hub. Was the bearing tight to press on the shaft?

  • Like 1

I didn't do the pressing, but it seemed to be what I'd call a 'good interference fit' like what I'd expect it to be really.

It was a bugger the get the hub out of the old one!

That's bad luck mate.

Is the hub bent?

Excessive rear camber?

Excessive driveshaft angles?

The two best ways to fit the hub to new bearing WITHOUT using a press:

Ensure your hub is completely clean.

1. Find a workshop that specializes in electric motor rewinds. Get them to use their induction (bearing) heater to heat the bearing & fit the hub.

2. Ring a cryogenics supplier, get 5 litres of liquid nitrogen (around the price of JD) from them in an insulated drink container (like a willow 5lt). Pour liquid nitrogen into a Styrofoam box sufficiently big enough to hold the liquid & the hub. Tie wire around two of the studs so you create two 'handles opposite each other. Drop the hub into the liquid nitrogen. Once the liquid stops bubbling, the hub temp has equalized with the liquid. Pull the hub out & drop it into the bearing. All done & no chance of bearing damage.

Now, if you don't have anything else to freeze & fit, experiment by freezing o rings, eggs anything. You can even run your hands through it, just don't leave them in there too long!

post-493-13922011276516_thumb.jpgpost-493-139220113771_thumb.jpg

Scotty, having done a few of these, is the hub pressed far enough into the bearing? To me, it looks like it needs to go in another 3-4mm or so.

I don't think the bearing has been sitting on that chamfered bit on the driveshaft?

In terms of freeze fitting, I just don't have time to organise all that, as good as it sounds. I need to do thus tomorrow so I can get the kids to school Friday

It may do, I can't see a great deal in the pics, I would need to inspect it. I do know stagea hub shafts don't line up with the back of the bearing, similar to yours.

I suspect rattling up the driveshaft nut would pull it tight though if it was newly pressed on anyway, although you wouldn't rely on it. Did you lube the hub shaft up first?

Do you have someone local with a bearing press to try and push it down some more? Or you might be able to buy a cheap one... It takes around 5 ton to crack the old bearing off the hub, and 1 ton to press the new one on, so a cheap press from ebay could pay itself off in one car.

I've dropped it off with a workshop to swap the hub over.

The hub wasn't lubed when it was pressed into the bearing from memory.

The guy at the bearing place said there wasn't any obvious signs of installation failure.

How do you torque up that big nut Scotty? I don't have a rattle gun, but left it in gear and used a big bar to do it up tight. The guy at the bearing place suggested doing it up as tight as you can and then putting the wheel back on and doing the final torque with the wheel taking the load rather than the diff/drive shaft

I just use my air rattle gun, I bought it as I couldn't crack the nut with a 2M breaker and me standing on it. Seems to work fine, and it's a fairly heavy torque rated gun.

I have had to replace new bearings before, one was just yesterday. Probably been on the car a few months but made noise soon after it was installed. Perhaps it was pressed incorrectly by the last mech, or just a dodgy brand? I have had no issues with the OEM or Febest bearings I have fitted for people.

533 RYC's suggestion is great if its easy enough to get hold of all of that stuff, but for a more low budget soloution you can use an oven and a freezer. Overnight in the freezer and 20mins in the oven (at about 100 degrees or so) should give a good enough temperature difference to make it alot easier

Liquid nitrogen is awesome shit.

Creating a temperature difference between the 2 is definently a great way to do it, because if its done right it usually literally falls together.

However if the specialist you've taken it to says he cant see any signs of incorrect installation, then you may have to look for other issues before installing another bearing. It seems to me like if you are having problems with 1 bearing then something is wrong on that hub or shaft, if its a problem with 2 or more, then it might be an inferior bearing (this is rulling out a bad install)

Bearings arent that fragile when installing, As long as you are hitting/pressing the inner race and not the bearing cage, you shouldnt do any damage to it

Just put the new bearing in, done everything up and all seems ok.

There is zero play if I try and move the wheel in the direction of positive and negative camber.

However I can get the tiniest bit of play if I move it in the direction of in and out in terms of toe adjustment.

Everthing is tightened up, could I be feeling one of the bushings in one if the suspension arms?

Paranoid now with the slightest bit of play :(

Tie rods would be the issue, they love to flog out on the inner ball end joint that connects to the rear steering rack ends.

I had play on the LHS and a tiny amount on the RHS. Ordered in 2 new tie rods from RHD and fitted them up.

No more play :) Same pn. as a 33GTS-T lol.

Ok, that makes sense. I can't feel any play from the bearing, it's like the whole hub/arm has a slight play in it.

At least I'm 99% sure it's not the wheel bearing now, which was the cause of most of the play

We use induction heaters for bearings, gears, shafts & achieve the same growth with up to 100 degrees less than using an oven, even when looking at a .003''- .004'' interference.

If not using a press, that sort of interference usually requires liquid nitrogen (CO2 will only get you around the .002'' mark), when shrinking is required.

Anyone know the interference between the inner race & hub?

  • 2 months later...
  • 7 months later...

Chris, is your wheel bearing thats been on your wheel and working great purchased from CBC bearing as posted in your DIY thread?

Yep no problems at all, done almost 20,000kms on it. The other side needs doing now!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...