Jump to content
SAU Community

Recommended Posts

Hello :action-smiley-069:

I have a lovely set of Nismo LMGT1's for sale.

Made by RAYS for Nismo,so you know they are made JDM strong.

These are in excellent condition with hardly a mark on them (as pics indicate)

They also come with RARE Rays centre caps!

Wrapped in Dunlop R compound tyres.2x tyres are on the wear bar & 2x tyres have about 30% tread left.(tyres are still very driveable)

They are 18x9.5 with an offset of +14.They fit nicely on-

R23 Gtr

R33 Gtr

R34 Gtr & anything else you can squeeze them under.

These will clear big brakes.

Nismo LmGt1's are hard to come buy these days in good condition. Also these were made in late 2002 (as date indicates in pic)

Located on Southside of Brisbane. Welcome to come pick them up if your local.

Interstate buyers I can organise freight to you (at your cost) & generally around $130 delivery Australia wide through e-go.com.au.

Im looking for $2500

Best to call or text me as im not always on here 0452-389-598

Ready to bolt on and drive away!

post-70521-0-29357800-1395629077_thumb.jpg

post-70521-0-15721400-1395629104_thumb.jpg

post-70521-0-96892900-1395629370_thumb.jpg

post-70521-0-53622300-1395629399_thumb.jpg

post-70521-0-44247500-1395629425_thumb.jpg

post-70521-0-27495500-1395629448_thumb.jpg

post-70521-0-18456100-1395629469_thumb.jpg

post-70521-0-65942700-1395629502_thumb.jpg

post-70521-0-62817200-1395629525_thumb.jpg

post-70521-0-60797700-1395629550_thumb.jpg

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/440941-nismo-lmgt1s-exelent-cond-18x9514/
Share on other sites

Pure sex. I wish I had a spare couple grand.

Those things are mint. Don't budge on price, they are worth every bit of $2,500.

  • 2 weeks later...
  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...