Jump to content
SAU Community

Recommended Posts

I am the original owner having bought this car in 2001. This car has been used as a daily driver and has never been mistreated. The car has garaged and serviced regularly with quality oils and parts.

I have used high quality name brand parts and I hope I can remember all the inclusions over the last 13 years. The reason for sale is that Ms. Wolv is the proud owner of a new, slower and lardier Korean car so I am moving my plates over to the RS4S.

This is a regretful sale, will suit the buyer who is looking for a car that is in very good condition, quality parts fitted, tuning by one of the best in Sydney and nothing more to spend for the next few years.

The car is registered until February 2015. The car has 240,000km on the clock. I changed the original engine (compression was good) for a lower km Stagea engine. Timing belt, waterpump, idler bearings, and all belts were changed at the same time (less than 20,000km ago).

Car: Nissan Skyline GTS-t series 2

Drive train: 5 speed Manual RWD

Engine: RB25Det

Colour: Silver

Kms: 240,000

Price: $11,000

Reason for sale: Missus has bought a new car so 3 into 2 doesn't go

Location: Hills District Sydney/Western Sydney

Contact: 0407 669166 or pm.

Modifications:

Garrett GT3076 56 trim comp 0.82 turbine twin scroll housing V-band rear

HKS cast manifold extrude honed, low mounted externally gated (suitable for T3 or T4)

Plazmaman FMIC

Jim Berry Clutch higher clamp organic

Apexi pod filter

Alloy intake

Greddy Profec B type II

Apexi Power FC + Datalogit + Wideband

550cc injectors

Bosch 984 fuel pump

Bilstein shock absorbers front/rear

Kings Springs front/rear

Whiteline adjustable swaybars front/rear

Camber adjustable eccentric bushes front/rear

Polyurethane bushes, pineapples etc

Aftermarket castor rod pickups (front end turn in is exceptional)

UAS (Bosnjaks) brake master cylinder stopper

Venom 5" cat

3" straight through exhaust, quiet exhaust note. Will supply rear cannon if you like the sweet RB sound

Splitfire coilpacks

Fenix 42mm alloy radiator

Volk Racing Wheels

JVC KDR926BT

Focal splits

Audison SRx3 amp

JL Audio 10" subwoofer hidden

Sound deadening installed inside front doors and under rear seats

IMG_3012.jpg

IMG_3011.jpg

IMG_3014.jpg

IMG_3013.jpg

IMG_3015.jpg

UnigroupDyno223122011_0000.jpg

That is a very very old tune which was done 3 years ago. Do you have any more recent dyno paper?

And? Makes no difference dude. Ignition/Fuel maps don't change by themselves with age lol

Can't believe you're selling her!!!!!!!

Ferk it's clean, you sure take good care of your car mate!

Good luck!

I can vouch for this car its clean as a whistle top shelf mods and tune! Car has power everywhere it really is a great drive! If you're in the market for a 33 give ya money to this guy and drive away in this silver bullet :)

Just realised you used an overlay of my 98 tune lol!

Edited by Mick_o

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...