Jump to content
SAU Community

Recommended Posts

Hi fellas,

I started this topic to see what kind of results some guys are getting on an engine dyno around the 600hp+ mark. In particular, actual engine torque values and rpm it is achieved (instead of measured by rolling road dyno).

So, anyone tuning on an engine dyno and have some torque figures to share; nothing specific, RB26, RB26, RB30... sorry if this topic is conflicting with the dyno result thread but it it more specific to engine dyno.

Thanks,

Mike

Link to comment
https://www.sau.com.au/forums/topic/442160-rb26rb30-engine-dyno-results-600hp/
Share on other sites

I have only ever heard of maybe two RBs being tuned on engine dynos, one RB25 making ~1400hp and one RB26 making ~1700hp - probably not too helpful for this topic, most people aiming for "only" 600ish are content with a rolling road or hub dyno :)

I have only ever heard of maybe two RBs being tuned on engine dynos, one RB25 making ~1400hp and one RB26 making ~1700hp - probably not too helpful for this topic, most people aiming for "only" 600ish are content with a rolling road or hub dyno :)

600hp+.... they can post it in here!

I know BoostdR had some results, I can't find it however. It was an RB30 with twin -10s that made good strong power.

I don't know of any tuners or engine builders here who have an engine dyno - the only ones I have seen are in a Polytech and one in a place doing research on fuels - which is not to say that there aren't some somewhere. I have seen a video of an Aussie speed shop somewhere that has one.

There are a few in Adelaide; most would not go to the trouble of an engine dyno but IMO it is the best way to tune and run in an engine prior to fitting it to the car. Also the only way to get a true reading of torque (and engine power).

There is one up our way, costs by the time you wire it all up etc are a bit steep, we were thinking to do the run in and basic tune on it and makes life simpler if you want to inspect the engine internally or work on it, in our case we are still unsure if its the right thing for us.

Maybe. maybe not.....

Yeah mine was done in Adelaide prior to me buying it.

2.8l with turbonetics GTK850 25psi on 98 with 10% meth-- 760hp & 780nm @ 5500rpm from memory.

Will try and find the sheet.

Thanks Richard, I will have a look for BoostdR's result somewhere on the forum today too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...