Jump to content
SAU Community

Recommended Posts

Hey

I've done searches in regards to this, but there are differing opinions and not many proper answers...

I've dumped oil plenty of times. This time though, after letting the oil drain for about an hour, I went ahead and put in fresh oil. But I've accidently overfilled...

It's 4L engine + .4L oil filter on a RB20DET. Engine has done 150k.

I put about 4L in, let it sit, had a look at the dipstick and it showed above H. Went for a small drive, let it sit again, but still sitting about 4mm too high. The dipstick shows the oil level about 4mm above max. and it just touches the letter H.

Should I drain some out?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/443919-rb20det-oil-overfill/
Share on other sites

Nah no dents, sump is all good. A fair bit of oil must have remained even after draining...

I think the best thing to do is simply get it at the correct level.

I'll see if I can drain some without undoing the plug completely, otherwise I'll dump the lot and then put it back in at the appropriate level.

Nah no dents, sump is all good. A fair bit of oil must have remained even after draining...

I think the best thing to do is simply get it at the correct level.

I'll see if I can drain some without undoing the plug completely, otherwise I'll dump the lot and then put it back in at the appropriate level.

Just to recap.

You come on here asking if the oil overfill is ok.

2 people say it is ok.

You somehow decide you should drain it.

Seems odd.

  • Like 1

Just to recap.

You come on here asking if the oil overfill is ok.

2 people say it is ok.

You somehow decide you should drain it.

Seems odd.

I don't know why you'd say that, I get asked for help all the time and it goes roughly like this:

*phone rings*

Me: "Hello"?

Caller: "Hi I need your help with X, it's doing Y"

Me: "I know what the problem is, you need to do Z"

Caller: "I don't think so, I reckon it's.............."

every. single. time.

I think people are just f*cking useless at asking for help.

To weigh in on the original conversation I fill between the H and the hump on an oil change (in an RB25 you can just dump 5L in if you have drained it on a level surface). I assume the hump is the danger zone much like there's a hump on the low side as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • http://calfinn.com.au/product/1500kg-standard-trolley-jack-cj-2t-c/1500kg-standard-trolley-jack-cj-2t-c   I have this and fits under a S3 33 GTR with no issues. Purchased in 2009 and not one issue. It was $950 back then. Not cheap but something so important isn’t worth cheaping out on.
    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
    • Perhaps the answer is... more jacks!* *proper jacks must be used.  
×
×
  • Create New...