Jump to content
SAU Community

R34 Electrical Issue's

crissy

By crissy,
in General Maintenance

 Share

Recommended Posts

crissy Explorer

crissy

Posted
Posted

Hello, I have a 1998 R34 coupe and im having some weird problems.

The other week i got in to drive it and when i unlocked it problems started,

1. The tacho and speedo dont work,
2. The bell chime for door didnt chime,
3. The interior light stays on,
4. The passenger door wont lock with the button on the remote or drivers side panel.

It still starts and drives fine,
I disconnected the battery and reset the ECU which worked, but then it happened again and again now that trick only works sometimes.

Any ideas? Cheers

Link to comment
https://www.sau.com.au/forums/topic/444407-r34-electrical-issues/
Share on other sites
Deza3000 Proficient

Deza3000

Posted
Posted

I reckon you should get it checked by an automotive electrician. Sounds like brittle cables between the battery and the accessories. Could also be a shorted PCB. I had a similar problem with my r34 in regards to the power windows, ended up being brittle wiring on the drivers side, causing the passenger side window to wind down but not up. Yours is a bit more complicated, i dont think its something that will just go away.

sleptema Proficient

sleptema

Posted
Posted

Hello, I have a 1998 R34 coupe and im having some weird problems.

The other week i got in to drive it and when i unlocked it problems started,

1. The tacho and speedo dont work,

2. The bell chime for door didnt chime,

3. The interior light stays on,

4. The passenger door wont lock with the button on the remote or drivers side panel.

It still starts and drives fine,

I disconnected the battery and reset the ECU which worked, but then it happened again and again now that trick only works sometimes.

Any ideas? Cheers

Tacho + speedo: Take out the dash, check for lose plugs.

Interior light and bell chime for door could be linked (as i'm guessing with the switch on "DOOR" it stays on?, but "OFF" it turns off?) Guessing it is the switch inside the door playing up. Where that little rubber piece is.

Passenger door: Does it lock when you flick the door lock internally, like the actual switch? Does it unlock with the controls on the passenger door?

Deza3000 Proficient

Deza3000

Posted
Posted

Tacho + speedo: Take out the dash, check for lose plugs.

Interior light and bell chime for door could be linked (as i'm guessing with the switch on "DOOR" it stays on?, but "OFF" it turns off?) Guessing it is the switch inside the door playing up. Where that little rubber piece is.

Passenger door: Does it lock when you flick the door lock internally, like the actual switch? Does it unlock with the controls on the passenger door?

I was under the impression that its all just one big problem?

#@crissy

Did these arise all at the same time? Or did the car just start having more and more problems? If its the second question then id go with what sleptema suggested.

sleptema Proficient

sleptema

Posted
Posted

I was under the impression that its all just one big problem?

#@crissy

Did these arise all at the same time? Or did the car just start having more and more problems? If its the second question then id go with what sleptema suggested.

I don't think they can be related, or he would be having issues with the entire car, not just those 3-4 things. I believe the tacho and speedo gain their signals from the Engine computer, where the door lock and chime is body control computer. Tacho gets its feed from the CAS, which can in no way be related to the door locks. And if it was the ECU, I doubt the car would be running smoothly. I don't want to jump to ecu replacement when it is most likely small shit,

sleptema Proficient

sleptema

Posted
Posted (edited)

The ecu gets the speed signal from the speedo.

The tacho gets its signal from the ecu.

Weird hey.

And the ECU gets is signal from the CAS. The speedo gets its signal from the WSS yes, the ECU doesn't read the speedo, the gauge is an output from other sensors.

Sensor (input) -> ECU (processer) -> Actuator (output - in this case, gauge)

I'm saying the tacho and speedo are more than likely related, but the tacho/speedo combo isn't related to the door locks as they are on completely different circuits.

Edited by sleptema
533 RYC Proficient

533 RYC

Posted
Posted

And the ECU gets is signal from the CAS. The speedo gets its signal from the WSS yes, the ECU doesn't read the speedo, the gauge is an output from other sensors.

Sensor (input) -> ECU (processer) -> Actuator (output - in this case, gauge)

I'm saying the tacho and speedo are more than likely related, but the tacho/speedo combo isn't related to the door locks as they are on completely different circuits.

Yes, the ECU gets it signal from the CAS, the ECU drives the Tacho.

The speedo gets it's signal from the gearbox output shaft, the same place as the ECU.

The wheel speed sensors are traced back to the ABS/Attessa ECU. The only time the ENGINE ECU references WSS is during traction loss (traction control for rear wheel drive only).

  • 2 months later...
Phyco Apprentice

Phyco

Posted
Posted (edited)

Hey, Just wondering if you got anywhere with resolving this crissy? They are all connected in some way, as I have exactly the same issue. I have narrowed it down to the either the ODO/Speedo/Tacho cluster or one of the cables running into it, as generally by giving it a bit of hard tap or removing and reconnecting one of the cables from behind the cluster the issue goes away (until next time). It's funny when starting the car as you don't get the reverse beep or have the doors lock, and then all of a sudden everything happens at once, like a delayed reaction.

Edited by Phyco
Phyco Apprentice

Phyco

Posted
Posted

Narrowed mine down to a contact issue on the TK20 Brown Connector (fuel gauge side) at the back of the cluster, as it has inputs/outputs for all the affected items (Door Locks, Reverse Chime, Speedo, Tacho, Engine Temp etc) just in case that is of any help to anyone else in future!

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...