Jump to content
SAU Community

Just Picked Up An Arx

polyarkos
 Share

Recommended Posts

polyarkos Explorer

polyarkos

Posted
Posted (edited)

Hi Guys and Gals,

JP here, thought I'd introduce myself.

As the title shows I've just bought a 3.5l ARX. Fresh import from Japan with 93,000km in silver with black leather interior and all the electro gizmos (including indicators on the mirrors). Having come from a 2005 Legacy GT I'm very happy with how this car runs and the trim level.

So far its had:

- Engine oil (15w40), air and oil filters done

- New brake pads all round with new rear rotors and machined fronts

- Interior lights changed to LEDs

- Reverse lights changed to LEDs

- MAF and throttle body cleaned

- New Enasave tires on factory wheels (not my preferred choice)

My to-do list is:

- Diff/transfer case oil changes

- Transcooler and Transgo shift kit with fluid change

- "Z-tube" and plenum spacer, just cos I can

- Upgrade the Bose stereo to a 2din head unit/screen

- Change the oil to 5w30 or 0w30

- Spark plugs

Currently I have a minor issue. The engine sounds like its revving very high, like a whining or supercharger sound that increases with speed from 40kph (even though the tach is saying its under 2000 rpm). I'm thinking either the brakes are sticking (they haven't bedded in yet), the wheel bearing are shot, or possibly the tires are just loud.

Is there any way to confirm this before taking it into a garage? Its loud, and coming from a car with a full 3" exhaust it is very noticeable.

Anyway, I'll post some pics up shortly. Thanks in advance for any advice or ideas on the above issue.

JP

Edited by polyarkos
Link to comment
https://www.sau.com.au/forums/topic/444744-just-picked-up-an-arx/
Share on other sites
polyarkos Explorer

polyarkos

Posted
  • Author
Posted

If the whining noise is noticeable while cornering, then it's the wheel bearings. It's rare to have both sides go at the same time.

Its loud and noticeable even when driving in a straight line, I'll check if it gets worse when cornering tomorrow.

Thanks

Daleo Grand Master

Daleo

Posted
Posted

Sounds a lot more like noisy tyres to me, are they just cheapy compliance tyres?

A noisy wheel bearing will also tend to manifest under braking as well.

Good luck with it, welcome to the forum.

polyarkos Explorer

polyarkos

Posted
  • Author
Posted (edited)

Sounds a lot more like noisy tyres to me, are they just cheapy compliance tyres?

A noisy wheel bearing will also tend to manifest under braking as well.

Good luck with it, welcome to the forum.

Its noticeable from 40kpm upwards whether I'm accelerating, cruising or braking.

I'm not sure about the tires, they are Dunlop RV503 Enasave. They were on the vehicle when it arrived of the boat, basically new with a lot of tread - supposedly an fuel saving tire.

Will check tire pressure tomorrow, maybe that will help. As far as I can find the 4wd Infiniti G35 hubs and bearings share the same part number 40202-24U00 so possibly a DIY fix.

Edited by polyarkos
polyarkos Explorer

polyarkos

Posted
  • Author
Posted

I took the long way to work to see if the noise got worse with aggresive cornering and breaking. Seems to make the same sound the whole time from 40kph upwards, accelerating, cruising or braking.

I'll see if a garage can give some advice.

polyarkos Explorer

polyarkos

Posted
  • Author
Posted

Checked the tire pressures tonight, all 4 sitting on 28psi. Pumped them up to 40psi and the car seemed less noisy, but not by much. I'll see how it goes over the next week and I might even see some improvement in economy too.

andy65b Veteran

andy65b

Posted
Posted

Wheel bearings failing at 93'000km's...... That is not a good sign for the accuracy of the km's the car has travelled.

My 03 ARX had 169'000km on mine when sold and had no problems with wheel bearings.

polyarkos Explorer

polyarkos

Posted
  • Author
Posted

Wheel bearings failing at 93'000km's...... That is not a good sign for the accuracy of the km's the car has travelled.

My 03 ARX had 169'000km on mine when sold and had no problems with wheel bearings.

Personally I don't think there are many cars coming into NZ with legit KMs. I am yet to find a dealer that will provide the auction sheets if requested.

Having said that the car looks in really good condition and I do expect stuff to wear out (at least I know I'm good for a while when they are replaced).

Artwear Contributor

Artwear

Posted
Posted

Hey mate, I have the identical issue with my axis. Over 40ks and it sounds like a airplane bout to take off! Have had tyres rotated, balanced and camber adjusted all to no avail. Also had 3 diffrent mechanics drive it and all conclude its tyres. Havent had coin to change em, so cant confirm or deny it being the fix. But im in the same boat and tyre's would be my outsourced opinion.

polyarkos Explorer

polyarkos

Posted
  • Author
Posted

Hey mate, I have the identical issue with my axis. Over 40ks and it sounds like a airplane bout to take off! Have had tyres rotated, balanced and camber adjusted all to no avail. Also had 3 diffrent mechanics drive it and all conclude its tyres. Havent had coin to change em, so cant confirm or deny it being the fix. But im in the same boat and tyre's would be my outsourced opinion.

This is exactly whats happened to mine. I got a garage to check the bearings as a road test was not conclusive. Spoke to Dunlop and they say the tyres are supposed to be very quiet....unless they have begun to sepparate.

Put the car on stands, remove the tyres and see if there is play in the bearings are they are noisy or catching when you rotate the axle. This will help to narrow things down.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

I have changed many front wheel bearings on these, new and old. They seem to wear out quickly, especially if they were replaced by incompetent mechanics. Bearings need to be pressed in correctly or they will make the same noise as the old bearings and quickly fail.

You can't always feel slop in the bearing as there are two races, unless one race has failed completely.

Can't you just borrow a set of wheels of someone to try?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...