Jump to content
SAU Community

Recommended Posts

Hey all

a mate has a r32 gtst and the old rb20 has given up the ghost.

its a registered turbo rb20.

I have a spare rb25 in the shed.

my question is, how do you go legally registering a 25 in a 32?

To get it on the papers would u have to go through regency?

Or is it an acceptable engine swap?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/446647-r32-engine-swap/
Share on other sites

Variety of answers. For mine it was regency and make sure have adequate brakes on the front that suit the weight addition - i.e. R33 front calipers etc., or 4-pot type-M R32 gtst brakes. That was from my experience. Though, you wouldn't want to keep the RB20 gearbox with an RB25DET under the hood...went through 2 gearboxes with the RB20, so chucked the 25-box in with the RB25.

Link to comment
https://www.sau.com.au/forums/topic/446647-r32-engine-swap/#findComment-7362385
Share on other sites

I looked into this when I had my 32. The best advice I got was to buy a front cut from an R34. Chuck in the brakes, motor, gearbox and wiring and go from there. Costs a bit but those motors are brilliant and if you put that motor in on the original gearbox you will blow them as mentioned

Link to comment
https://www.sau.com.au/forums/topic/446647-r32-engine-swap/#findComment-7362386
Share on other sites

Coil overs are fine as long as the ride height is legal. That mod is fairly easy to make legal as long as the brakes are done. Making the wiring work is a different story however haha

Are you sure about that?

It's my understanding in sa they have to be engineered and have a mechanical way of limiting how low they can be set.

Link to comment
https://www.sau.com.au/forums/topic/446647-r32-engine-swap/#findComment-7363198
Share on other sites

Are you sure about that?

It's my understanding in sa they have to be engineered and have a mechanical way of limiting how low they can be set.

It'll be different in every state. Australia is fun like that. But yes it has to be engineered but apparently there isn't much of a drama in doing so at a legal height. This is according to an engineer I spoke to around 2 years ago. Things may have changed since then and be different in different states
Link to comment
https://www.sau.com.au/forums/topic/446647-r32-engine-swap/#findComment-7363306
Share on other sites

  • 1 year later...

https://www.sa.gov.au/topics/transport-travel-and-motoring/motoring/vehicles-and-registration/vehicle-standards-and-modifications/engine-and-exhaust-modifications

Basically submit the form, you'll get a list of requirements needed.

Fulfil those requirements, do the tests, pay money and get a form saying its all legal...

Wont necessarily mean you wont get defected for it, just means you can roll through regency without issue (whilst paying them to inspect you're paperwork saying it's legal).

Link to comment
https://www.sau.com.au/forums/topic/446647-r32-engine-swap/#findComment-7654690
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...