Jump to content
SAU Community

Recommended Posts

Hi all,

I've got a few parts lying around that I no longer require. Located at Newmarket/Ascot Vale area. Prefer pick up at this stage but may post some items later down the track. Pm me if interested.

1. BC BR Coilovers - $700 - Good condition - In the car for about 20,000 km's.

2. C34 manual conversion parts - $1100 - never got around to converting the car to manual. What you see is what you get + gearbox from late model R32 GTR which isn't pictured.

3. C34 auto LSD - $350 - purchased used and never fitted.

4. Transgo shift kit - $200 - purchased from group buy - New

5. C34 radiator air deflector - $120 - purchased from group buy - New

6. Rear cargo light - $100 - purchased used and never fitted.

Cheers,

Kandio

post-77155-0-17905100-1408400450_thumb.jpg

post-77155-0-26998500-1408400488_thumb.jpg

post-77155-0-51071600-1408400519_thumb.jpg

post-77155-0-49349400-1408400561_thumb.jpg

post-77155-0-20767400-1408400595_thumb.jpg

post-77155-0-41597300-1408400627_thumb.jpg

post-77155-0-73133700-1408401522_thumb.jpg

Edited by Kandio
Link to comment
https://www.sau.com.au/forums/topic/446995-vic-c34-series-1-parts/
Share on other sites

Hi all,

I've got a few parts lying around that I no longer require. Located at Newmarket/Ascot Vale area. Prefer pick up at this stage but may post some items later down the track. Pm me if interested.

1. BC BR Coilovers - $700 - Good condition - In the car for about 20,000 km's.

Cheers,

Kandio

just wondering will the coilovers suit a series 2 260rs?

Price drop!

1. BC BR Coilovers - $650 - Good condition - In the car for about 20,000 km's.

2. C34 manual conversion parts - $1000 - never got around to converting the car to manual. What you see is what you get + gearbox from late model R32 GTR which isn't pictured.

3. C34 auto LSD - $300 - purchased used and never fitted.

4. Transgo shift kit - $180 - purchased from group buy - New

5. C34 radiator air deflector - SOLD - purchased from group buy - New

6. Rear cargo light - $800 - purchased used and never fitted.

Cheers,

Kandio

  • 2 months later...
  • 2 weeks later...

Wondering if the coil overs would suit my s2 rwd

Front definitely won't. Have a look at your front end vs a awd. Way different. Rwd stageas basically have s14 front setup.

Rears will fit, but it would be silly to split them.

Edited by Ben C34
  • 5 months later...
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...