Jump to content
SAU Community

Another Rb25 Top Feed Injector Thread

mynameisdaniel
 Share

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

GTSBoy
GTSBoy

Oh, not this shit again. You are the ONLY person in the entire world who cares about it.

GTSBoy
GTSBoy

Or you could just call Scotty.

JordansR32
JordansR32

Well the car is still a street car so I was trying to keep the "factory" looking engine bay, but guess i have gone well past that now haha, doesn't help when I have the external wastegate on the rear

Posted Images

89CAL Grand Master

89CAL

Posted
Posted

Anyone used the EV14'S from sonic performance? I need the dead times for them and when I emailed them and asked they said something about tuners are using the same base settings across 1000 cc injectors in the market

89CAL Grand Master

89CAL

Posted
Posted

Yeah I figured as much, but it just seemed an odd thing for him to say. Just wanted to make sure

I found settings on the Deutschwerks website that I was going to go with but when I got the email back its thrown me for some reason

All good. Waiting on some plugs to arrive ready to make the new injector harness at the moment then ready for some smooth running, especially after Johns experience with some modern top feeds. Although the Nismo's I have are a bit nicer then the Five-O motorsport ones I imagine, so not as much of an upgrade :P but still should be great.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

I just started with 0.85ms at 14volts with mine and kept dropping it till I was happy.

Most tuners would just set a higher deadtime and lower it till the idle is lean and stable.

I remember when I had the Five-O Garden Hoses injectors, the spec sheet said 0.54 at 14v LOLx10 I couldn't get them to idle until they were set at 0.89ms

  • 9 years later...
samw/skyline Contributor

samw/skyline

Posted
Posted
On 8/27/2014 at 10:08 PM, Dose Pipe Sutututu said:

got the kit from clean-injection from the states, uses Siemens DEKA injectors and comes with convertor plugs so no need to chop away at the OEM loom :)

post-22311-0-53965100-1409191801_thumb.jpeg

thank you for mentioning these guys. I was getting a headache trying to find a fuel rail and injector combo for my needs and these guys have just what i need for cheap. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • Kapr
      Freddy Plenum vs Genuine options RB25

      By Kapr · Posted

      @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Holy shit... wow!!! I totally missed this
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...