Jump to content
SAU Community

Recommended Posts

Ive been doing an rb25 into s13 conversion on and off for a while now. Im putting the harness in but I cant seem to find the air regulator plug. I know of the AAC plug (the purple one) but cant find the other one. Is it part of a separate harness?

Link to comment
https://www.sau.com.au/forums/topic/447089-cant-find-air-regulator-plug/
Share on other sites

I think it will be PWM controlled by the ECU. The other plug that you dont have (which is brown in the photo I have, on the valve itself) goes to a solenoid so will need PWM to allow varying amounts of air through

Now there's a solenoid? :P lol damn

I cant take pics as the car is at my brothers work shop but googling around, the plug im missing is blue. The plug that goes into the AAC is purple (have that plugged in) and there is a brown plug I have nfi where it goes. Im guessing that's for the solenoid?

Stupid car....

My sister has a Series 2 R33 and is bone stock. I think im going to have a look at it and see what im missing. I think I have that solenoid in my parts bin somewhere...

Edited by Gameboy

The air reg is simply a 12V bi-metallic strip valve, nothing flash.

No ecu input, just power on when the IGN is on.

Doesn't even need 12V, engine bay heat will eventually shut the valve.

A pain to access on a 25, impossible on a 26.

I hate them.

Not to be confused with the purple plug idle bump up for the aircon.

Or the brown plug for the AAC.

Of course this is presuming the OP is talking about an R33 Rb25 and not a Neo.

The air reg is simply a 12V bi-metallic strip valve, nothing flash.

No ecu input, just power on when the IGN is on.

Doesn't even need 12V, engine bay heat will eventually shut the valve.

A pain to access on a 25, impossible on a 26.

I hate them.

Not to be confused with the purple plug idle bump up for the aircon.

Or the brown plug for the AAC.

Of course this is presuming the OP is talking about an R33 Rb25 and not a Neo.

Thanks for the post. Its a great help and yeah, its an r33 25.

Thanks guys, love this forum. :thumbsup:

Just as an added extra people used to power these cold start air valves off the fuel pump circuit say with a relay . The idea being that if the ignition was on for any length of time without the engine running the valve wouldn't be heating and closing up .

As mentioned most engines had these valves mounted somewhere where they got coolant heat early in the warm up phase so that if the power feed failed they'd still heat up and close .

How does the Neo system work .

A .

Although the air reg is IGN "ON" for power, it's actually all part of the fuel pump relay power feed which is controlled by the ecu.

So once the ecu times out the fuel pump, power to the air reg is also cut.

Attached is Rb26 system, 20 and 25 are similarly controlled.

post-73571-0-41421200-1408662898_thumb.jpg

Yes Cal, the brown plug (AAC) is ecu controlled, varying duty cycle signal.

Your purple plug is the idle bump up for air con, just an on/off solenoid not hard wire linked to the engine ecu.

Of course your aircon control unit (amplifier) does tell the engine ecu to control the compressor's magnetic clutch.

Found a photo of the Rb26 air reg, buried under the plenum.

They all look the same, 20, 25, 26, 30......horrible things.

post-73571-0-54062800-1408676043_thumb.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...