Jump to content
SAU Community

Recommended Posts

Hi all,

Ive searched about everywhere but nothing seems to be the same issue that I may have.

Doing auto to manual conversion in m s2 r33 gtst bought the conversion kit with absolutely everything down to the ecu came with loom from manual thru to power cable at fuse box this loom has on it Knock sensors, starter motor power, starter solenoid power, 3 cables to connect to manual, power steering solenoid ect im sure I have forgotten a few.

My question is I removed 2 separate sort of looms when removing the auto 1 was connected to the auto only and ran right up and pluged in at what I can only describe is the front chassis rail drivers side near radiator. The second loom had all the knock sensors and starter motor crap on it

The loom I removed has a lot more plugs than the one supplied with the conversion kit does this sound normal to people can anyone enlighten me or do I have to get the wiring diagram and go over it myself im hoping for the lazy way out and one of you guru's can give me some advice.

cheers,

Link to comment
https://www.sau.com.au/forums/topic/447272-manual-conversion-help/
Share on other sites

  • 7 months later...

I've just completed the ,annual conversion and have wired up the reverse lights and the neutral sensor correctly. Now I am just wondering the speedo and oil pressure gauge are not currently working and the power steering is slightly heavy and hicas light is on. Assuming I have not wired these up as the plus is different on the manual gearbox loom.

Anyone confirm where the wires are or n which plug on thE car side (car originally an auto).

Thanks

Manual speedo sensor is in approximately the same spot on the lower right hand side of the manual box as it is on the auto box.

When you say "have wired up" does this mean you have run fresh cables for those switches, or does it mean that you have put in the manual driver's side engine bay and gearbox loom like the OP did? Because putting in the whole side loom is far easier than doing it in bits and pieces. Regardless, the original 2 wires for the auto speed sensor will just as happily carry the pulses from the manual's speed sensor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...