Jump to content
SAU Community

Recommended Posts

Hey guys

The engine in my r33 gtst is getting a full makeover. The final result should show well over 300rwkw. I have been reading on the Internet on how to get flames out the exhaust after giving it a boot?

If you degut the carry or whatever it's called will you still get in trouble or will they see it has a cat and not know its gutted?

Also when it says the car is running rich. Does that mean you run it richer then normal or will it still blow flames on a normal tune just without the cat.

Cheers

Tyler

Link to comment
https://www.sau.com.au/forums/topic/447291-degutting-cat-for-flames/
Share on other sites

Yes gutting the cat will assist with flames, but it's a terrible reason for getting rid of that cat which is a critical part of the exhaust system. If it is a street car i highly advise leaving the cat alone or replacing it with a high flow metal one. It takes all the nasty chemicals out of the exhaust and traps. Without the cat you will not pass an emissions test if you have to pass one for rego whatever state you are in. If you gut the cat its still pretty easy for a switched on policeman to tell, just stnad behind the car when you rev it and it stinks, whereas nowehre near as much smell with the cat.

Getting caught withwout/with a gutted cat is a maximum penalty of $16,000 if i remember correctly.

Have fun.

Grab a fuel injector. Weld it into the exhaust system with an ignitor. Wire it all up with an activation button under the clutch pedal. SICK WAN!

But seriously..

Skylines get enough unwanted attention without shooting flames. You might change your mind once you get done.

Grab yourself a nice venom cat! :thumbsup:

Hotrod used to use a spark plug in the exhaust, and let it run overly rich on deceleration.

That's how they achieved it.

I personally wouldn't worry about it.

How are you going to see them?

If to impress others, a car thats quicker with less flames will generally impress more.

Either way, good luck.

Hope you don't blow up.

Yeah screw it.

I don't want to lose the whole car or have to spend more because of defects just for some flames. Ill see how it is when its finished and spend the money on something else.

Good call !

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...