Jump to content
SAU Community

Recommended Posts

iv had cases of oil leaks before but asumed it was leaking from the oil catcher though i did get that replaced

now i noticed theres still leaks but its not coming from the catcher but from some sort of filter under the pod i think its a breather ?

iv attached a picture of how my catchcan settup is and where the leaking is from (brown shading represents oil leaks)

http://i.imgur.com/P3jxTH7.png

the catchcan itself seems literally empty

my question is why isnt the catchcan catching the oil? but passing down through the breather

The oil catch can doesn't catch the oil because it doesn't see any blow-by gases through it.

The catch can shall be between the rocker cover and the breather/intake pipe.

As is your catch can is totally useless.

ah i see this whole thing is plumbed incorrectly then and despite the several mechanics i went to about it didnt mention anything

even though the breather is before the catchcan wouldn't the can at least catch something other side of rocker cover?

i have a feeling the can might be installed incorrectly by the mechanic too lol

just figured that the breather/filter i was confused about was there to vent gases/oil to atmosphere instead of the intake

Edited by KrazyTurk

Yep that's a fairly retarded way to plumb in the catch can. It would only catch what's coming out of the inlet cam cover

How much is coming out anyway? A healthy engine none should come out.

  • Like 1

That means two things

1 your engine is tired.

2 your catch can sucks. It should be baffled.

Actually it doesn't necessarily mean 2 until such time as he sets the plumbing up properly and then oil still comes out the vent.

OP......you need the catch can to be in the path between the engine and the vent. Merge the two hoses from the cam covers together and hook them to one connection on the catch can. Connect the vent to the other port on the catch can. Run it and report back. If the can works, then there will be oil in it. If the can doesn't work (per Ben's suggestion above) then there will be oil in it and oil outside it!

worth noting that the filter/breather is a bad idea. Hook it up to the turbo intake.

1. It's illegal

2. the filter material will become soaked in oil and drip. also it's a fire hazard

3. Supposedly exposing the crank case to vacuum from the turbo will help keep the rings on their seats with a worn engine. I don't know how true this is.

4. Also if you've got blowby, and I assume you do. then boost is escaping from the combustion chamber into the crankcase where it is venting to atmosphere. typically you want this to recirculate to the turbo's inlet. I'm not sure if this would affect AFR's though

Anyway, hook up the catch can between the rocker covers and the compressor inlet. That should allow you to tick all the boxes of legality while keeping oil out of your intake

  • Like 1
  • 3 weeks later...

so i hooked everything up correctly and now noticed smoke coming out from exhaust pipe?

Ok that indicates that oil fumes are getting though the catch can so you need to baffle the catch can and/or put an air/oil seperator (could be another baffled catch can) into the line from the catch can to the turbo intake. If there is masses of oil coming out at WOT refer to the oil control thread for more answers.

When you say hooked it properly most people would take that as you hooked it up the proper way, with the catch can venting back to the inlet.

Are you sure it's hooked up properly at the moment?

That's not hooked up properly. That filter on the far right.....shouldn't be there. That hose should be hooked up to the turbo inlet pipe, so that the air that flows through the catch can into the engine has been through the AFM. We explained all that already.

It's a shame even after being told how to do it you still do it wrong, and are adamant that it's correct.

It's wrong.

Simple as that. If you don't understand that's cool, get someone who knows what they are doing to do it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...