Jump to content
SAU Community

Recommended Posts

Hello all,

I have scored another 32moredoor gts4(scored it mega cheap...), when I bought it the engine had been played with.
Has had FFP and topmount td06-20g-external gate installed, fmic, stock injectors, stock coilpacks, stock afm(green label), stock ecu(still untuned after installs).
I have seen the car running before all installs and it was mint.

Has also had alarm/immobiliser and switch to disengage the front diff installed (have herd of immobiliser screwing with some cars)

On cold start I have to feed it to get it to start and idle which it only just does, once running it struggles to run, misses like crazy(sounds like a rough subaru) and overfuels(can smell it) sits on about 500rpm then stalls out.

Ecu is telling me code 43 but I have had multimeter on the TPS wiring and all is good voltage wise but nothing changes when its running and I disconnect the plugs on the side. Has been swapped out for a known working tps and same problem.

Didnt think a turbo and plenum swap would throw everything out so much???
Blows a bit of white smoke which im guessing is fuel.
Havent kept it alive long enough to get warm incase its something major.

All the coilpacks are fine and plugs seem to be ok aswell, swapped out ignitor and no change

Also there is NO change in idle etc when I unplug the AAC etc...

I have looked into most things and am about to send it to a shop but would rather save the $$$ for when I get nistune/afm/injectors/TUNE but dont want to do all that and find out the motor is ROOTED!!!!

I attached a before and after of the engine, did a massive tidy up/clean while trying to find the root of the problem, has all new vac lines etc now. Can upload a video of it trying to run if that may help.

post-116531-0-74971200-1413098241_thumb.jpg

post-116531-0-45967000-1413098439_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/449625-rb20det-help-please/
Share on other sites

unfortunately for you, running aftermarket turbos on the factory ecu can make the engine grenade on boost. I would suggest a comp test at the minimum.

Check AFM wiring, and maybe for vac leaks. Although a vac leak usually leads to a high and lean idle.

white smoke is usually a bad indication but it could have been condensation in the exhaust if the engine hasn't fully warmed up yet.

note; if you do a comp test don't forget a wet test as well to get an idea of the piston ring condition

So did the car get hammered with the new stuff on it or just started and it was running crap?

As Blackkers said if it got a hard time with the new turbo etc it would have easily killed the engine.

Coming from an sr20 background I have been lookign at the pvc and aac scraching my head actually.....looking at all the treads about these and they just make me scrach my head more lol....

I have a broken hand atm so having trouble pulling it apart so havent gotten to taking the pvc out

The whole plenum set up has me scraching my head actually. Been wondering if having ALL vac lines for wastegate etc coming straight out of the plenum might be confusing the ecu a bit? not currently running a bov so no vac in cooler piping only the 3 coming out of the plenum as you can see in pics....

had a little tinker before and pulled aac off and cleaned it (was sooo full of carbon) then set the idle on the side of that which had it running a bee's d!ck better

Your pcv setup won't be helping.

^^^ Agree, is there even a PCV valve there? looks just like a fitting then hose to rocker cover. Will be sucking un metered air.

You mean the fitting on the firefall side of the ffp?

Edited by Noddy42

You mean the fitting on the firefall side of the ffp?

I think they might be concerned by the open breathers on the cam covers.

If you are from an SR20 background, then setting up the various connections on an FFP on an RB should be simply a case of making them look and do what they do on an SR. Same things have to go the same places.

I think they might be concerned by the open breathers on the cam covers.

If you are from an SR20 background, then setting up the various connections on an FFP on an RB should be simply a case of making them look and do what they do on an SR. Same things have to go the same places.

Thats easy enough then, should be all good.

Will block them all bar one and see what that does

Your pcv setup won't be helping.

^^^ Agree, is there even a PCV valve there? looks just like a fitting then hose to rocker cover. Will be sucking un metered air.

You guys where spot on, the pvc valve is still in the stock plenum and thats just a open fitting...... going to change it now. Cheers guys

By the way. It's PCV, not PVC. PVC is a type of plastic.

LOL sorry.... to much pvc at work.

PCV was some of the problem, noticable differance, now it starts/turns over and stalls straight away, I can baby it at 1000rpm but as soon as foot comes off it stalls. WAY WAY less fuel smell now but a hint still there.

Thanks shitloads guys,

still getting the error code 43/tps wiring tho.... anyone know of anything else that would cause that to come up? voltages for the tps seem sweet as and has been swapped for known working one.

Whoever did the plumbing of the all vac lines & breather lines should be revoked of his man hood and grow a vagina..

You need to plumb back OR block the PCV line going back into the plenum as the car is still running an AFM.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...