Jump to content
SAU Community

Recommended Posts

Hey guyzzzzzzzzzzzz

Was wanting some low end response from my evo, (to gain some better initial acceleration from a stop), was thinking of cosworth 264 camshafts and tomei valve springs...

Initially i had planned on doing fuel pump and injector upgrade for an e85 tune, but thought of doing cams first so i can get more out of the tune. Ive also been told that ill get more response out of the car by switching to e85. Thinking whether to just dump the whole camshafts/valve springs idea and save a few pennies and just get the e85 tune, or to go for the camshafts as well.

Anyone got any suggestions on how i go about this?

Currently running 180awkw @21psi on 98 octane stock turbo tuned for response.
Current mods:

- turbo back exhaust
- bigger intake pipe between maf and turbo

- HKS panel

- Tune

I dont really plan on going hard out on the top end power, that would just be a bonus, im really keen for some good response and decent gains along the rev range(especially low to mid).

Cheers (:

Link to comment
https://www.sau.com.au/forums/topic/451195-upgrades-for-response/
Share on other sites

More response? Maybe get a big block v8.

But seriously. My mate has a evo 8. They have great response.

E85 will give you a fatter power band. I know you evo guys love wacking cams in. But if you are strapped for cash get a flex tune. Changes the car immensely.

  • Like 1

More response? Maybe get a big block v8.

LOL v8s zzzzzzz, not a fan :P

Haha yea it responds great! But in comparison to some new cars that i have come across (335i, audi, c63 amg, even evo 10s),my initial throttle response/takeoff seems so mediocre, i hit power at 3000rpm, losing a bit of time on takeoff. Guess the AWD also has a part to play, and the fact that i hate launching.

Hahahaha ive seen some evos go hard with cam and turbo upgrades but not sure how much of an improvement camshafts are without other bolt ons (i.e. bigger turbo), i dont know if cams will justify the cost considering what i want.

Flex tune is a tune for a variation of ethenol levels yea? Senses the amount of ethanol in the system and adjusts timing accordingly?? I was actually keen on doing that for a few months, cant make up my mind haha.

Yes. That is what a flex tune is. 98 - e85

Sweet, ill see how i go with a flex tune.

Do you recommend any fuel pumps? I was going to buy the walbro 455lph e85 pump, but apparently they draw too much voltage ?? Fuel pump relayyy maybe? Or different brand?

C63 amg is a v8. Everything you drove except the evo 10 has higher capacity motors. So there is No point comparing Apples to oranges. If you really want response then get a tiny turbo. Done

Yea i realize that, I just assumed its the RWD drivetrain and valve timings that made them so responsive, considering the BMW 120d is also pretty responsive. Evo 9 and 10 also have the variable valve timing (mivec) as well as a much bigger turbo than its predecessors with very minor turbo lag, hence why i thought cams would do the trick. Anyways flex tune all the way! I have a united that supplies race fuel(which i assume is e85) near my house so thats convenient.

You need to check to see if that is e85. It might be 100 Ron fuel.

Maybe it draws too much voltage for the stock wiring. But run New wiring to the pump with a relay and it would be sweet. Probably best to read up what the evo guys like to run. Walbro make a few e85 pumps.

As Hadouken said and most things I have read on the site would indicate, smaller turbos and smaller cam duration for response , under 260s, maybe 250 ish seems to get them going pretty quick.

I think Mick"s cams are in the 250 range and he said they are great for response, hope my memory is working, sorry Mick haha?

.

Maybe it draws too much voltage for the stock wiring. But run New wiring to the pump with a relay and it would be sweet. Probably best to read up what the evo guys like to run. Walbro make a few e85 pumps.

No problem, just spoke to a tuner, they said the exact same thing you did, new wiring and a relay, 100 bucks for all that including installing the pump so should be sweet, would of done it myself if it was just simply swapping out the pump but ahh well. Rather get it done right the first time.

As Hadouken said and most things I have read on the site would indicate, smaller turbos and smaller cam duration for response , under 260s, maybe 250 ish seems to get them going pretty quick.

I think Mick"s cams are in the 250 range and he said they are great for response, hope my memory is working, sorry Mick haha?

I actually just did some research on the turbos, turns out the evo 9 and 8mr turbo features the titanium compressor wheel, which is why they spool much faster than the 4/5/6/7/8 (excluding 6.5), funny thing is my turbo only has the 9.8t housing which is smaller than the 10.5t housing on the 9. (by which according to the laws of physics smaller housing should spool faster?)

I was leaning between 256 or 264, ill see how i go. Would i need to retune the car if i get cams done on a later date?

  • 1 year later...

No , only the 9RS got the turbo with the Titanium Aluminide turbine and Magnesium compressor wheel . Can't remember what the part numbers are but the second version of that turbo is better because it has a "Super Back" compressor wheel while the earlier ones are flat back and can fail if pushed hard .

All Evo 9s used a turbo centre housing with a larger integral compressor housing back plate and its matching compressor housing uses a larger diameter diffuser section . I believe the Evo8 MRs and all 9s used a revised 10.5cm turbine housing with a mirror imaged "D" shaped waste gate outlet that was supposed to flow better than the twin holes and flat valves that say an Evo 6 10.5cm turbine housing has . I think the later ones were supposed to be less likely to crack than the early 6 style ones .

Lots of detail things changed from Evo 8 to Evo 9 engines and it was aimed at having a bit more low down torque with better consumption and emissions .

The 9s were reasonably heavy for a 2L car and a combination of different head/variable inlet cam timing/turbo changes/more boost/closer ratio six speed box made a better overall system than earlier Evos had . Also each 4G63T from about E6 on had better rods and pistons to cope with the boost increases , from memory 9s had something like 18 lbs boost std and the 10s about 21 pounds . 

Also MiVec was more than just the variable inlet cam timing , revised (enlarged) cooling passages between the head and block - and the heads deck was thicker . They use motorbike sized spark plugs and improved coolant flow around the hot sides of the chambers and exhaust ports supposedly made them a little more detonation resistant .

In the US most people don't play with anything less than an Evo 9 based turbo because you get better housings which get the most out of std or larger wheels .

Those 9RS turbos come on a little earlier and have a bit better transient response because of the lighter wheels less inertia to overcome . The TiAl turbines with fail at high boost levels because the bonding between the wheel and shaft can only take so much loading . Probably smart to run std Evo 9 boost levels with them which is quick enough on the street I reckon .

A couple of years back an Aussie won in class a Pikes Peak event with a very well put together standard sized Evo 8 turbo , the proof of the pudding is the run times not the boost or kilowatt numbers .  

Just my 2c , cheers A .

 

   

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...