Jump to content
SAU Community

Recommended Posts

Hi all. First off I'm no expert in skyline engines. Now thats out of the way.

Block I'm using is a s2 block. Std crank spool h beam rods and arias -10.4cc forged pistons. Block will get the usual jobss done acid wash hot tank and bored 40th to 87mm. Will be decked to zero deck height. Will use a 1 mm head gasket and neo head. Head is currently in the car on 25 neo engine. Head has been ported with stage 1 pon cams. Flywheel is from extreme billet lighten flywheel. 6 puck sprung button clutch. Inlet will be a greedy copy manifold with 1000cc bosch injectors. Hot side is custom made hi mount manifold by myself in t3 form to a gtx3582r garrett ball bearing item. Fuel will flow via 2 bosch 044 pumps. Will start with bp98 fuel then change over to e85 later on. Nistune will control all the electronics. Spit fire coil packs will fire the good stuff.

If anyone has same sort of set up would appreciate input as to what power I should be able to expect.

Link to comment
https://www.sau.com.au/forums/topic/451449-rb30-25-neo-build/
Share on other sites

301 to 399 rwkw. Too many unknowns. Is it going to be fully balanced with a new harmonic balancer and revved to 9000+ or standard and limited to 7000? Build and tune all count for a lot. You may end up with a sky high compression ratio which will be a problem unless you have access to E85. Don't use Bosch pumps - get something more modern, quieter and E85 friendly.

Those pistons are vl turbo spec.

Have you already bought them?

If not look seriously at something with less or no dish to get the comp up. The days of low comp have been and gone.

If you already have them, no worries, boost it up!

Looks like boost up as I have them already. For 700 delivered not going to complain. Will deck the head and use as thin as possible gasket. Head is fitted with cams 256deg and 9.15mm lift. E85 is available easy access. Will be balanced annd haven't set a rev limit yet

Besides this engine is going into a lc torana witch is around 400+kgs lighter than a r34 skyline. Neos run 9 to 1 comp but are 2.5lt engine. This is a 3lt engine. Off boost shouldn't be too bad as the 30det's only run a mid 7 to 1 comp. Off boost in a vl they are fine.

If 0 deck heights min HG thickness is 33thuo for clearance

I think the dish is a bit big can you machine them down 40-60thuo and then deck block to match

I run 14cc dome top with 0 deck hieght and 1.1mm HG with 63cc combustion chamber ( 26 head ) and have +/- 9.5:1 state CR

I can machine the pistons down 40th and take 40th off the head. 8.44 to 1 was working on 1mm hg. By doing pistons and head machine work will bump it up around 9 to 1. Have looked at the 30 hybrid pages and read verrious builds but not close to what I'm building. Haven't seen any other builds with neo head and gtx35

I've got the bulk of my engine together now

Rb30, Neo head,

Spool I beams

Wiseco 9cc dish pistons.

.051" gasket

Head studs main studs

Standard head and cams to start with but has springs and ti retainers

CPC plenum 6boost manifold gt35

6x LS2 coils

Running a .001 deck height and we had to deck the head down to 46cc ending up with high 8 comp.

I'm hoping to make around 400-450hp with the standard cams on 98 (auto)

Hey lcxu105

I think you may have messed up there with your gasket thickness. Because you're using mm but you are using inches measurement for the gasket. The gasket should be 1.295mm

Using the calculator above. mine comes out to be about 8.94:1

using the summit racing calculator (which allows to you to change hg to inches or mm) I get 8.98: 1

Mind you I could be wrong

Edited by Huzqld

Huzqld you're comp ratio will be a high 9.6 to 1. Mine with a .51 hg and 50cc head wwill be 8.96 to 1.

you have to put the HG thickness in in MM on that scale setup, so you have put in .51mm not 51thou which is closer to 1.3mm

Edit, should have read the whole page before posting lol, Husqld beat me to it :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...