Jump to content
SAU Community

Recommended Posts

Hi Guys.

So I'm in the process of testing a Sniper NOS kit in my NA 25GT R34.

Everything is installed and working, including both the nitrous arming switch and micro switch which is enabled on when foot is to the floor on the accelerator.

I've tested it by pulling off the intake and putting my foot down while the NOS is armed and it sprays fine.

I went for a test drive last night after completing the setup but when I had my foot down, i didn't feel a noticeable difference (75HP Jets). It felt like the car was starving.

Has anyone dealt with nitrous systems before running a stock fuel pump and encountered this issue? I started off testing with the 35HP jets and had a similar issue, so I'm just trying find where the problem is.

P.S. anyone have a rough idea how much nitrous a stock RB25DE would be able to handle? I've got aftermarket extractors and a 2.5" cat back exhaust

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/452651-nos-in-r34-rb25de/
Share on other sites

need a tune or nothing will happen, not to mention your afr's will be all over the place!

could potentially be damaging your engine, also don't you need an injection of fuel next to the nos jets?

I've never used nos and only know this from seeing other cars setup.

2 guys above, do you realize the sniper is a wet kit,?

Meaning fuel gets injected along with the nitrous.

Of course going onto a Dyno would be the easiest way to sort it, but as a budget approach not always an option.

I would be closely monitoring fuel pressure as the stock pump might not be up for it.

Based on how tough rbs are I would think they could take a fair bit if nitrous, what the factory ecu does is another story.

By your explanation it sounds like the pump isn't up to it.

Also you can buy wideband o2 kits for under 150, that would be a wise investment.

Good on you for gassing it!

  • Like 1

Hey guys,

Thanks for your input.

I figured out the reason it wasn't working correctly and it was because the fuse was tripping. I had it wired to the cigarette lighter. I wired it directly to the battery with a fuse in between and seems to be working fine. Not sure why it felt like it was starving tbh :/

Had the car on the dyno today and 75hp jets gained me 35hp atw. Will be putting 125hp jets in at the drags next time I'm there and see how it does. Fuel pressure was fine, but it sure didn't feel like it when i tested it, still surprised of what the cause of it was.

An aftermarket ECU for it will make a big difference according to the bloke who dyno'd the car.

Now... to look for an aftermarket ECU for an r34 rb25de neo. Anyone know of any available? Any help will be appreciated!

Thanks

2 guys above, do you realize the sniper is a wet kit,?

Meaning fuel gets injected along with the nitrous.

Of course going onto a Dyno would be the easiest way to sort it, but as a budget approach not always an option.

I would be closely monitoring fuel pressure as the stock pump might not be up for it.

Based on how tough rbs are I would think they could take a fair bit if nitrous, what the factory ecu does is another story.

By your explanation it sounds like the pump isn't up to it.

Also you can buy wideband o2 kits for under 150, that would be a wise investment.

Good on you for gassing it!

Sorry to hijack the thread, where can I find this wideband for under $150? I can't seem to find one for under $450, thanks.

Sorry to hijack the thread, where can I find this wideband for under $150? I can't seem to find one for under $450, thanks.

Crazy cheap

Scotty nm35 recently bought one.

http://www.wide-band.com/widebandproducts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...