Jump to content
SAU Community

Parts Clean Out! R32/33 Gtr Nismo Trust Greddy Cusco Ksp Attain Rasty Fj20 Rb26

CameronBNR32

By CameronBNR32,
in Classifieds

 Share

Recommended Posts

CameronBNR32 Proficient

CameronBNR32

Posted
Posted

I have sold my GTR so no longer need the parts/spares.

All parts are located in Brisbane south side, and inspections are welcomed, just message me on here or email me and I will try and get back to you as soon as I can.

I will post at buyer's expense, so if you are located elsewhere and if you are interested, please contact me for a quote on freight.

Images are located for all the parts here: http://www.sau.com.au/forums/gallery/album/5783-classifieds-images/

Thank you.

BCNR33 GTR Skyline RB26DETT Camshaft/Timing Covers

One of the camshaft covers has been damaged with a part of it snapped off.

$150

FJ20 Cylinder Head with front cover/oil pump

Bare FJ20 cylinder head

Front Cover with Oil Pump

$500

Trust/Greddy Hard Intercooler Pipes

Only have two of the pipes out of the set of four.

$100 each

Greddy T78 33D Turbo

http://www.trust-power.com/spec_swf/02turbo/Turbo%20Chargers.htm

Split pulse design, rated at 720hp

Removed due to going to a twin turbo setup

$1500

Greddy Type R Wastegate

http://www.trust-power.com/02turbo/waste_gate_valve.html

http://www.trust-power.com/spec_swf/02turbo/GReddy%20%20Waste%20Gate%20%20Valve.htm

Removed due to going to a twin turbo setup

$500

Greddy Type R Split Pulse High Mount Exhaust Manifold

http://www.trust-power.com/02turbo/sus_turboex_manifold.html

http://www.trust-power.com/spec_swf/02turbo/Sus.Turbo%20Ex.%20Manifold.htm

Stainless Steel Split pulse design.

Removed due to going to a twin turbo setup

$1000

Greddy Heat Shield

http://www.trust-power.com/02turbo/heat_insulator.html

Removed due to going to a twin turbo setup

$50

R33 GTR Dash Cluster

Reason for removal was swapped out for an aftermarket cluster.

Has 26,000km on Odometer.

$300

R33 GTR Fuel Pump Controller

$50

R33 GTR YAW Rate Sensor

$100

R33 GTR RB26DETT Alternator

$100

BCNR33 GTR Skyline N1 Centre Triple Gauge Cluster

R33 GTR N1 centre triple gauge cluster

Worked perfectly before being removed from the vehicle

$100

Nissan Skyline GTR RB26DETT Carbon Fibre Timing Belt Cover

Unknown Brand

I impulse bought it when I was in Japan.

$50

Nismo Skyline BCNR33 Series 3 Front under Diffuser

http://www.nismo.co.jp/products/catalogue_2014/#page=265

Genuine Nismo S-Tune aero body kit front under bumper spoiler for the Skyline BCNR33 R33 GTR Nismo S-Tune front bumper.

Paid around $1000 and then realized it wouldn’t fit!

$500

Nissan Skyline BCNR33 GTR N1 RB26DETT Air Box and Snorkel

Nissan Skyline BCNR33 GTR N1 Air Box and Snorkel

K&N Air Filter

$250

RB26DETT Air Flow Meters

These were working fine before being removed from the vehicle, one is genuine and one looks aftermarket.

$100 for the pair

Trust/Greddy 3.7” “Power Extreme” Ceramic Coated Stainless Steel Exhaust with Custom Front/Dump Pipe

Hardly used, was only pulled off due to going back to a twin turbo setup on the car.

Custom made dump/front pipe to suit 4 Bolt turbo exhaust flange. No catalytic converter. :whistling:

$600

KSP Racing Equipment / Attain Carbon Kevlar Rear Bumper Cover to suit Nissan Skyline R33 GTST or GTR

http://www.ksp-eng.co.jp/ATTAIN/exterior/36.html

Brand New still in box

KSP/Attain Brand

Carbon Kevlar

$150

Rasty FRP Boot for Skyline R33 GTR/GTS-T

http://www.rasty.tv/pro/trunk.html

Flat Truck Style painted in QM1 White

Some Cracks in the paint where the wing was mounted.

Very light

$450

R33 GTR Front Lower Arms

Stock R33 GTR Front lower arms with ball joints.

$150 for the pair

Nismo Clear Indicators

Brand New Still in Box.

$80

R33 GTR R200 Competition Diff

Brand New Cusco 2 way Center

Brand New Crown Well and Pinion

Trust/Greddy Extended High Capacity Diff Cover

http://www.trust-power.com/16power_train/diff_cover.html

http://www.trust-power.com/spec_swf/05engine/DiffCover_Up_Grade_Kit.htm

Diff Cover has also been modified to clear a close fitting exhaust

4.11 Ratio

$2000

R32 GTR Dash Speedo

Reason for removal was only due to being swapped out for an aftermarket cluster.

52,000km on Odometer.

$250

R32 GTR Factory Suspension

Inserts and springs.

They were removed while they were still in good working cond.

$400

R33 GTR ABS Unit

Removed from the car only due to installing a pedal box set up.

$250

R33 GTR Washer Bottle and Motors

Very good condition.

$50

R33 GTR RB26DETT Cylinder Head

Complete cylinder head with coil packs.

Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened.

$1250

RB26DETT Ind. Throttle Bodies and Plenum.

Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened.

$400

RB26 Starter Motor

Was working perfectly and was only pulled off the engine.

$100

R33 GTR Sump and Factory Front Diff

Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened.

$300

  • 1 month later...
  • 1 year later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...