Jump to content
SAU Community

Recommended Posts

Pro

less restriction , potentially more power

Light weight :)

Cons

Illegal.

Environment hazard

Louder

A straight pipe makes way more sense than a bent one in place of a cat.

Couldn't figure that out yourself?

Edited by Ben C34
Link to comment
https://www.sau.com.au/forums/topic/453860-decat/#findComment-7480023
Share on other sites

Yer i gathered louder and more flow which could mean possible power gains, wasnt sure if it could potentially be harmful to the car in any way, still abit of a newbie so wanna make sure i know what im doing before i do it, i read some where that straight pipes are not good for dailys for some sort of air flow reason which is why i askd any cons about the straight pipe

Link to comment
https://www.sau.com.au/forums/topic/453860-decat/#findComment-7480038
Share on other sites

For a street car just get a good 100cell cat. You should at least make some effort to keep your car legal and not pollute the environment way more than you have to.

Decat will mean you have much blacker exhaust smoke under power (which is a give away to the cops) and your rear bar will be dirty from it.

Link to comment
https://www.sau.com.au/forums/topic/453860-decat/#findComment-7480051
Share on other sites

There is one other thing being missed.

Even a high flow cat is a waste of time if it does not meet EPA standards, there are rules to the standards and if you want to meet them expect some sort of restriction, most 100 cells dont pass emissions you may as well have no cat.

Otherwise a straight pipe through a cat shell is the way, looks like a cat but isnt, get called in for a test bolt on a stock cat.

Exhaust notes dont change much (very little) with or without a cat, a cat is not a muffler which is designed to muffel sound, its a chamber with a cell substrate inside.....

Link to comment
https://www.sau.com.au/forums/topic/453860-decat/#findComment-7480110
Share on other sites

Stock cats, especially on late model cars act as extremely good mufflers. Removing all 4 of them makes a huge difference. A highflow cat on the other hand makes no difference to exhaust noise.

My opinion, run a single 5 inch body 200cpsi euro 3 or 4 cat and enjoy a legal highflow cat that will flow 400+kw. Emissions testing is only going to become more stringent in the future, and a black bar will dob you in instantly.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/453860-decat/#findComment-7480126
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I think he was only proposing to use the wire, not the sender. Simply because it runs from the right place to the right place. Personally, I wouldn't hack up the factory wiring like that. I'd just lay in the Defi loom.
    • From memory it wasn't too hard to simply see which wire ran where when you plug that in. Unfortunately also from memory the OEM sender does not use the same configuration 99.9% of gauges run. So in other words if you connect the signal wire that was running to the OEM gauge to your DEFI gauge you might find your oil reads at 200C or some other incorrect value. I remember having the same line of thought and then running new wires/senders to match the gauges I have. The pinout is available in the R34 workshop manual.
    • Does anyone on here know which wire on the GTT triple gauge pod harness is for the oil temp gauge? my sensor works fine but I upgraded the gauges to DEFI advance. And if I can simply piggyback off the oem oil temp wire to the Defi oil temp sensor wire that would make life so much easier. 
    • Even face her a wash now that’s it worth more than my house
    • This was what I was invisioning, or Pete cutting a beer can up and hose clamping it around the catch can! Ha ha ha
×
×
  • Create New...