Jump to content
SAU Community

Recommended Posts

and who said modified cars from japan arent good value?

cleaning my car today i found an HKS F-Con computer piggybacked to my main blitz ECU.

Does anyone know anyone in perth who can tune these?? and the apporximate cost for tuning?

im currently researching them on the net, lumpy was going to be my first option, but if anyone has any other suggestions it would be greatly appreciated!!

Link to comment
https://www.sau.com.au/forums/topic/4540-who-can-tune-a-hks-f-con/
Share on other sites

Sorry to be the bearer of bad news but as HKS jealously guard their tuning software you'll have to take the car to Sydney for a tune........or Singapore.

That's unless someone has managed to get the software recently.

If Lumpy can't help try Lane at Race Torque in osborne park.

Cheers

Chris

UPDATE

speedworks cannot tune it either. so i have come to the conlcusion that this thing is useless

now what should i do?

my current management is;

blitz rechipped ECU with HKS PFC F-Con piggy-backed

im thinking, remove the HKS thingo and run an SAFC with the rechipped ECU. but then people are telling me that AFCs are only a 'toy' and shouldnt be used

remap the remapped std ECU. people also say that this is not tuning in real-time and is therefore unreliable....

i cant afford a full replacement so options are

1)leave

2)afc and no hks piggy

3)no piggys or controllers, just remapped ECU

thoughts? suggestions?

adam 32, you've already peiced together the story with these things, but I thought I'd add my experiences anyway.

At one point, I was looking at buying a used PFC-Fcon (+ GCC) from the eastern states for about $200. Heres what I know:

- pfc-fcon is a essentially rom based fuel only computer that talks directly to injectors via harness. Not programmable and no timing changes.

-The rom comes programmed from factory for basic mods and replacement roms are only available through hks.

- HKS claim extra tunability via an add on device, the GCC. It makes modifications to the air flow meter signal, so really nothing special, basically an overpriced 1st gen s-afc (can be used with or without the pfc-fcon).

If you can find a GCC somwhere in your car (small black box with 5 dials), then you're laughing. Take it down to your fav tuner and let them tune it like a s-afc. Otherwise, leave it in until you figure out what to do long term. I'd be thinking remap or basic e-manage package (until you can afford the harnesses you want).

Most probably, yes. But I wouldn't expect it to be cheap (standard hks rip off prices) and it still won't change timing.

Oh yeah, if its connected to the car right now, I'd be careful about removing it. The Biltz ecu may have been tuned in unison with the pfc, so pulling it out could change the fueling maps. Maybe a check by a tuning shop before and after its removed to make sure it doesn't run too lean.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...