Jump to content
SAU Community

Recommended Posts

Too wide across the 30mm measurement. As in the lips on the bush, sit a bit too far past the edge of the bracket.

Also too wide across the 33mm measurement, such that it's quite difficult to get into the bracket. I could remove material in that direction but would still have the issue with the lips sitting too far out across the 30mm measurement.

Ability to move around inside the bracket back and forth as the lips are not being used to assist in retaining the bush. I assume though that most of the force used to keep the bush in the cup comes from being pressed against the car itself by the bracket.

I'm going to grab the bushes and quickly re-test them on the way home. From memory it was a good 1mm per side that they were too wide.

Surely there should just be a damn bush that fits when everyone talks about this being a "bolt on" mod. Nobody else seems to have ever mentioned changing brackets or modifying bushes.

I'm also considering that if I thin the bush too much it could wear through/tear at those thin points rather than just using the right bush/bracket.

Edited by ActionDan

Valid point.

I will re-test them on the way home. Just annoyed that this is supposed to be such a simple mod yet nobody has documented this which makes me think I'm missing something, wrong bracket, requires certain bush, etc.

Putting one of these into my S13, but unsure what D Bush to buy. SuperPro has them up to 24mm, but the bar seems to be 25mm (admittedly measured with adjusting shifter with measuring marks, tape backs this up but both could be 1mm out). I've also read some people state t's 26mm. Nolathane lists odd sizes.

Can any shed one some light on this?

Also do I need to use grease on the bushes when installing them? Seems to be a lot o conjecture around this also.

A standard rear R32 GTR anti roll bar has an outside diameter of 25.4mm or 1" in old school imperial. Says so in the service manual.

Cross your fingers that they line up with the bolt holes on the car! The reason I slimmed down the front bushes on my car is that there wasn't room to fit a D with a bigger size between the stud and bolt hole. Any bigger D bracket I tried (not that I did) almost certainly would not have lined up with the fasteners.

Just did quick test fit. Brackets will fit car.

Just hit them with some primer and will satin black them later because I don't like the natural colour.

If I get a chance I'll fit the rear bar later but have been playing daddy day care while the missus is sick and out of comission.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...