Jump to content
SAU Community

Recommended Posts

Hi All,

I have read up about similar issues on the forum but still unable to locate my problem.

My stag has a miss at idle and in high rev range but not too bad though the middle I have changed coils and the car comes good for a day then back to missing again. Plugs are only 1000km old gaped to .8, new AFM. I have pulled the plugs out and the drivers side look really good but the passenger side look a bit black compared to the drivers side.

Please help, any ideas?

Link to comment
https://www.sau.com.au/forums/topic/454380-m35-stagea-missing/
Share on other sites

ok checks hoses, all look and feel ok.

I started unplugging coild packs 1 by 1, passenger side no change when removing drivers side as soon as i unplug 1 the car runs ruff.

Its only running on the 3 drivers side cylinders??? WTF??

anyone heard of this?

Also, check for error codes. Could be Cam pos sensor on left bank if there are no related mods like ecu piggyback, coil packs, etc.

Which plugs did you put in?

I used NGK Iridiums LFR6AIX-11 but gapped down to .8

I have checked for codes but there is nothing there...

It feels like a timing issue to me...I have swapped out the rear sensor on the left bank.

I used NGK Iridiums LFR6AIX-11 but gapped down to .8

I have checked for codes but there is nothing there...

It feels like a timing issue to me...I have swapped out the rear sensor on the left bank.

Good chance you damaged the plugs, they are too fine and brittle to gap down if you have done so.

I use LFR7aix, but a stock M35 should be fine running the hotter 6's. The plugs I use though are already gapped at .8mm, and I run mine up to 40psi without a problem on the original 14 year old coils.

Any sensor issues will be quickly picked up by the ecu and a fault light will be displayed. What the ecu doesn't know is if you plugged the coilpacks in the wrong order for example. It's very easy to mix the front plugs up, try swapping them around.

Good chance you damaged the plugs, they are too fine and brittle to gap down if you have done so.

I use LFR7aix, but a stock M35 should be fine running the hotter 6's. The plugs I use though are already gapped at .8mm, and I run mine up to 40psi without a problem on the original 14 year old coils.

Any sensor issues will be quickly picked up by the ecu and a fault light will be displayed. What the ecu doesn't know is if you plugged the coilpacks in the wrong order for example. It's very easy to mix the front plugs up, try swapping them around.

Cheers Scotty I will give it a go

Good chance you damaged the plugs, they are too fine and brittle to gap down if you have done so.

I use LFR7aix, but a stock M35 should be fine running the hotter 6's. The plugs I use though are already gapped at .8mm, and I run mine up to 40psi without a problem on the original 14 year old coils.

Any sensor issues will be quickly picked up by the ecu and a fault light will be displayed. What the ecu doesn't know is if you plugged the coilpacks in the wrong order for example. It's very easy to mix the front plugs up, try swapping them around.

Ok swapped out the plugs to the old ones (LFR6aix-p) no change, the front 2 coil plugs can't get swapped on mine as there isn't enough length in the plug wire..... ?

On the passenger side? The rear two can be mixed up then yeh? It's the coils where the plugs sit back to back you need to worry about, I have seen them mixed up many times, sometimes it's even my fault. :P

  • Like 2

checked again Scotty, but I was able to get any mixed up with my Stagea as the length of each plug will only go to 1 spot. I did change 3 of the spark plugs back to the old one and it seemed to make a bit of difference to the mid and top end, i will change out the other 3 this weekend coming as I don't have the car with me. I'm also replacing the PCV valve too see if that make any difference to the idle.

I have been also thinking of do an injector clean, good idea??? I'm thinking it cant hurt to do it....

If anyone else has any ideas, they would be greatly appreciated.

I can send you a refurbished set of injectors if you like, but that probably won't be the issue. You can most definitely mix up two of the plugs on each side, the ones that face each other where the plugs are nearly touching. Try it out before anything else...

I swapped over the plugs but it only just reached....you can see in the pic the front and middle are different lengths, the drivers side could get mixed up.

I'm really starting to lean towards injectors

Scotty if can pm me about the injectors you have, that would be great, unless any other ideas

post-39528-0-97955900-1426488980_thumb.jpg

ok yep, i swapped them around, no good.

i pulled the injectors, all good nice and clean, flowing nice.

i was having a listen to the exhaust and i think there might be something loose there and when the turbo comes on i can hear a different noise i havent heard before, im also using more fuel then usual, im going to have a look into the exhaust this weekend coming. could be a blocked exhaust all along.....

i love solving problems but i hope i can solve this soon cause its really giving me the shits!!! lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...