Jump to content
SAU Community

Recommended Posts

hey i just got pulled over again and this time they must have heard my bov so they called a traffic cop to assist cos he was supposed to know whats, i played the "i dont know anything card" but when he said my boost controller was a bov as well as a boost controller i told him he didnt know sh1t so after he threatened to get his pen and paper out and start to write down everything wrong with it shut up, anyways i dont wana remove the bov cos i would have to weld up the hole in the fmic piping so i want turn it to a plumb back but i need the plumb back adaptor for a turbosmart type3 ss, if anyone has one please let me know or if anyone has any ideas how to make it plumb back another way that would be good, i got the stock parts but it would be a pain in the ass to do the bov

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/
Share on other sites

For sale section or buy from a turbosmart dealer. There are going to be no 'other' ways to make it plumb-back that are going to be easier then buying the right adapter and hooking it up. The adapter will cost stuff all (probably $30, if I could get a Greddy one for that price I'm sure turbosmart are close)

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7492305
Share on other sites

Rule number 1 when pulled over, act resectfully to the police, act dumb (dont know much about cars), and hope they spot something basic on the outside to write the ticket for so they dont open the hood, thats the sort of defect that can be easy to clear as in most cases being too low of having tyres sticking out of the guards simply means presenting the car to Vic Roads (or whoever is the equivalent in your state) for a inspection to clear just what got written up and nothing else.

My sons been done for having tyres out of the guards twice and (too) lowered once, all 3 times put stock parts on, lady comes out and looks, sees stock height or wheels, defect cleared, aftermarket parts bolted back on the moment it got home, Hwy patrol are constanly looking at it now, we are starting to think they have gven up as im sure the previous defects show up yet the car is back as it was and all they do is stare now.

Think of being pulled over as a bit of a attitude test.

You need to plumb it back, your not allowed to vent to atmosphere, its a simple as that now.

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7492380
Share on other sites

yeah thanks for the advice, that is very good advice. Yeah i will plumb back the bov if i can get the adapter plate or i will have to put the stick one back on and as for the dual stage boost controller im a lil bummed out about having to remove that, the dumb ass only knew to look at that cos its bright blue and looks obviously aftermarket, i seen that i can put the stock one on and ground the wire to keep it in high boost but thats only 7psi and i want the whole 12 that it can take safely, so i was thinking about going a 12psi actuator that can simply replace the stock one and then i can paint it black and put a nissan sticker on it just in case so it doesnt stand out. Does anyone have one for sale or know where i can get one cheap, and are they pretty much generic fit or do i need one specific for the stock r33 turbo?

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7492746
Share on other sites

Why not buy a discreet boost tee, some black boost line and hide the boost tee where you cant see it? If you think you only got caught because it stood out, then hide it somewhere better.

I think the R32 GTSt actuators run about 10psi. Honestly though, without an aftermarket ECU I wouldnt bother running any more then 7psi. I ran 10psi in mine through the stock ECU and it hit R&R badly and just wasn't real nice. Even when I got boost to the right point where it would run till redline, it was still not great. Did the high boost mod to the standard boost solenoid and running around 7psi again it seemed so much nicer.

My advice, take it or leave it. Save some money, buy an ECU with in-built boost control (Link/Vipec etc, even the PowerFC can do it with the optional boost kit) and get it tuned. You will be amazed how much better it runs, and if the tuner is good you will get better fuel economy and so on

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7492879
Share on other sites

yeah i am so i would have to remove aftermarket one on the fmic and have the hole welded up and then i can put the stock one back on the cross over pipe and plumb it to the intake, unless i can track down the plumb back adapter for the aftermarket one and then i can just simply plumb that one to the intake. Its a pain in the ass lol

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7493527
Share on other sites

the original is a metal pipe that goes straight into the rubber air intake hose on the turbo and the other end just uses a bit of rubber hose to join the metal pipe to the stock bov, thankfully i still have all of the stock parts

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7494905
Share on other sites

finding right size hose proving to be a little difficult but may be able to modify original pipe to shorten distance to front mount intercooler piping where new bov is located & 35mm hose is not real flexable lol

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7495329
Share on other sites

  • 2 weeks later...

if the hose from the plenium to the bov was blocked would the bov stay closed permanently, or would pressure in the ic pipe force it open sometimes?

i thought about fitting the stick bov back on in the stock location and leaving my aftermarket one where it is and then finding some kind of valve so i can run the plenium vac hose to both bov and have the valve set so i can direct the vac line to goto whichever bov i want at the flick of a switch, as long as the bov that isnt turned on doesnt open at all.

I hope i have described this right

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7502178
Share on other sites

if the hose from the plenium to the bov was blocked would the bov stay closed permanently, or would pressure in the ic pipe force it open sometimes?

i thought about fitting the stick bov back on in the stock location and leaving my aftermarket one where it is and then finding some kind of valve so i can run the plenium vac hose to both bov and have the valve set so i can direct the vac line to goto whichever bov i want at the flick of a switch, as long as the bov that isnt turned on doesnt open at all.

I hope i have described this right

That's a bad plan.

The pressure from the plenum is required to keep the bov closed while on boost

Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7502191
Share on other sites

Seriously. Just run the stock one, or buy an aftermarket plumback one and plumb it up. If you really want to change the noise (this is the only reason I changed mine, because I don't like the stock BOV noise, not I wanted a hektik sound) then you can still change it with a plumback, and get none of the drawbacks of an atmo.

It's not worth the trouble of defects and getting harrased all the time.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/454499-bov/#findComment-7502245
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...