Jump to content
SAU Community

Recommended Posts

Guessed this was the write category if not just move it please admin

So a there's no really good write up on installing gtr headlights into a gtst

Going from h4 to h1/h3c

I've pretty much worked it out. As someone did a bad hack job in mine and it doesn't work! I have no headlights highbeams are constantly on etc

Question I have is what's easier to fit hids too the h1s or h3c headlights

Cheers in advanced

Link to comment
https://www.sau.com.au/forums/topic/454788-gtr-headlights-hid-fitment/
Share on other sites

I strongly recommend you read this thread:

http://www.sau.com.au/forums/topic/93963-xenon-hid-lights-conversion-for-r32/

If you're planning on throwing some cheap 6000+ Kelvin HID kit into your standard headlights, you're going to have a bad time.

Been there done that. To answer your question, you buy the bulb for the housing, e.g. if your headlights take H3C, then you buy H3.

Wiring wise it's pretty easy. Use a multimeter/test light if you must to figure out which bit on H4 plug is low and high (or can Google/Bing it).

Rip out all the old stuff and go from there.

No matter what kit you put in the standard projectors, the light output will be shit (thing pencil beam with lots of scatter).

The $30-50 eBay kits from China will die in a couple of months. The more expensive ones last a bit longer.

The kit I currently use (2 years running) is a fast start one that was almost $200. The equipment from The Retrofit Source are so cheap these days, you'd be fooling yourself not to buy from them.

Opening the headlights and changing the projector is a lot easier than you think. I did my second (current) pair of headlights within two hours.

The link I provided gives you a couple of options (including mine).

The difference between a retrofitted and a standard headlight with HID kit is so massive, you'll have to see for yourself (put cheap HID it into standard headlight, then go park next to a car with factory HID lamps).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...